Ferm WSM1008 - Page 8

8
EN
- the times when the tool is switched off or when
it is running but not actually doing the job, may
VLJQL¿FDQWO\UHGXFHWKHH[SRVXUHOHYHO
Protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
\RXUKDQGVZDUPDQGRUJDQL]LQJ\RXUZRUN
patterns
'(6&5,37,21),*$
Your wall slotter has been designed for making
slots in masonry. The machine is only suitable for
right-hand use.
  2QRIIVZLWFK
  /RFNRIIEXWWRQ
  /RFNLQJOHYHUIRUVORWGHSWK
4. Scale for slot depth
  'HSWKVWRS
6. Spindle lock button
7. Guard
  2QRIIVZLWFKIRUODVHU
  /DVHU
 2YHUORDGLQGLFDWRU
11. Base
12. Wheel (4x)
 'XVWH[WUDFWLRQFRQQHFWLRQ
 0DLQJULS
15. Auxiliary grip
 &DUERQEUXVKKROGHU
ASSEMBLY
Before assembly, always switch off the
machine and remove the mains plug
from the mains.
5HSODFLQJWKHFXWWLQJGLVFV¿J%
Worn or damaged cutting discs must be replaced
immediately.
 2QO\XVHVKDUSDQGXQGDPDJHGFXWWLQJGLVFV
- Always replace both cutting discs at the same
time.
 1HYHUDWWHPSWWRUHPRYHWKHJXDUG
Ɣ .HHSWKHVSLQGOHORFNEXWWRQSUHVVHGWR
lock the spindle (17).
Ɣ /RRVHQWKHRXWHUÀDQJHXVLQJWKHÀDQJH
NH\
Ɣ 5HPRYHWKHROGFXWWLQJGLVFWKHVSDFHUV
(21), the old cutting disc (22), and the inner
ÀDQJH,IQHFHVVDU\XVHWKHVSOLWWLQJ
wedge (24) to remove the spacers (21).
Ɣ ,IQHFHVVDU\FOHDQWKHÀDQJHV
Ɣ 0RXQWWKHLQQHUÀDQJHWKHQHZFXWWLQJ
disc (22), the spacers (21), and the new
FXWWLQJGLVF
Ɣ )LUPO\WLJKWHQWKHRXWHUÀDQJHXVLQJWKH
ÀDQJHNH\
Ɣ 5HOHDVHWKHVSLQGOHORFNEXWWRQ
USE
6HWWLQJWKHVORWZLGWK¿J&
The slot width can be set using the spacers
between the cutting discs. The number of spacers
between the cutting discs determine the slot
width.
 'RQRWVHWWKHVORWZLGWKGXULQJXVH
- Always mount at least one spacer between the
cutting discs.
Ɣ 'HWHUPLQHWKHVORWZLGWK
Ɣ 0RXQWWKHUHTXLUHGDPRXQWRIVSDFHUV
EHWZHHQWKHFXWWLQJGLVFV5HIHUWR
WKHFKDSWHU³5HSODFLQJWKHFXWWLQJGLVFV´
6HWWLQJWKHGHSWKVWRS¿J$'
The depth stop restricts the maximum slot depth
during use to prevent the machine from cutting
too deeply into the wall. The slot depth can be
read from the scale (4).
Do not set the depth stop during use.
Ɣ 6OLJKWO\OLIWWKHGHSWKVWRSIURPWKHJXDUG
(7).
Ɣ 6HWWKHGHSWKVWRSWRWKHUHTXLUHGSRVLWLRQ
Ɣ 5HOHDVHWKHGHSWKVWRSWRORFNLWLQWRWKH
correct position.
6HWWLQJWKHVORWGHSWK¿J$(
7KHVORWGHSWKLVYDULDEOHEHWZHHQDQGPP
The slot depth can be read from the scale (4).
Do not set the slot depth during use.
Ɣ 6ODFNHQWKHORFNLQJOHYHU
Ɣ 7LOWWKHEDVHWRWKHUHTXLUHGSRVLWLRQ
Ɣ 7LJKWHQWKHORFNLQJOHYHU