Ferm WSM1008 - Cleaning and Maintenance


EN
6ZLWFKLQJRQDQGRII¿J$
Ɣ 7RVZLWFKRQWKHPDFKLQHNHHSWKHORFNRII
button (2) pressed and simultaneously press the
RQRIIVZLWFK
Ɣ 7RVZLWFKRIIWKHPDFKLQHUHOHDVHWKH
RQRIIVZLWFK
8VLQJWKHODVHU¿J$
The laser is used for projection of the cut on the
wall.
Ɣ 7RVZLWFKRQWKHODVHUSUHVVWKHRQRII
switch (8).
Ɣ 7RVZLWFKRIIWKHODVHUUHOHDVHWKH
RQRIIVZLWFK
2YHUORDGLQGLFDWRU¿J$
7KHRYHUORDGLQGLFDWRULQGLFDWHVZKHWKHUWKH
machine is overloaded.
Ɣ ,IWKHPDFKLQHLVVZLWFKHGRQWKHRYHUORDG
LQGLFDWRUÀDVKHVJUHHQWLPHV
Ɣ ,IWKHRYHUORDGLQGLFDWRUOLJKWVJUHHQWKH
machine is not overloaded. The machine can
be used normally.
Ɣ ,IWKHRYHUORDGLQGLFDWRUÀDVKHVUHGWKH
machine is overloaded. Apply less pressure on
the machine.
Ɣ ,IWKHRYHUORDGLQGLFDWRUOLJKWVUHG
the machine is fully overloaded. The machine
will be switched off.
'XVWH[WUDFWLRQ¿J)
2QO\XVHWKHPDFKLQHZKHQLWLVFRQQHFWHGWRD
vacuum device which is approved for stone dust.
The vacuum device must be suitable for the
material to be worked. Use a special vacuum
device when working with toxic materials or
where toxic dust is produced.
 1HYHUXVHDKRXVHKROGYDFXXPFOHDQHU7KH
use of a household vacuum cleaner can easily
damage both your health and the vacuum
cleaner.
- Always use the dust extraction adapter.
 0DNHVXUHWKDWWKHKRVHRIWKHYDFXXPGHYLFH
is securely connected to the dust extraction
adapter.
 ,IWKHYDFXXPGHYLFHEUHDNVGRZQVWRSZRUN
immediately, switch off the machine, remove
the mains plug from the mains, and try to solve
the problem.
Ɣ ,QVHUWWKHGXVWH[WUDFWLRQDGDSWHULQWRWKH
GXVWH[WUDFWLRQFRQQHFWLRQ
Ɣ 7LJKWHQWKHGXVWH[WUDFWLRQDGDSWHUE\
turning it clockwise until it locks into place.
Ɣ &RQQHFWWKHKRVHRIDYDFXXPGHYLFHWRWKH
dust extraction adapter (25).
Hints for optimum use
Ɣ 'UDZOLQHVWRGH¿QHWKHGLUHFWLRQLQZKLFKWR
guide the cutting discs.
Ɣ +ROGWKHPDFKLQHZLWKERWKKDQGV
Ɣ 6HWWKHVORWZLGWK
Ɣ 6HWWKHGHSWKVWRS
Ɣ 7DNHRQHRIWKHIROOZLQJVWHSV
 /RZHUWKHPDFKLQHLQWRWKHZDOODQGVHWWKH
slot depth (recommended). The machine is
placed against the wall and the cutting discs
lower into the wall in order to set the slot depth
more accurately.
- Set the slot depth and lower the machine into
the wall.
Ɣ 3ODFHWKHPDFKLQHZLWKWKHZKHHOVRQWKHZDOO
0DNHVXUHWKDWWKHFXWWLQJGLVFVDOLJQZLWKWKH
drawn lines on the wall.
Ɣ 6HWWKHVORWGHSWK
Ɣ 6ZLWFKRQWKHPDFKLQH
Ɣ :DLWXQWLOWKHPDFKLQHKDVUHDFKHGIXOOVSHHG
Ɣ 6ORZO\PRYHWKHPDFKLQHDORQJWKHSUHGUDZQ
OLQHV¿UPO\SUHVVLQJWKHZKHHOVDJDLQVWWKH
wall.
Ɣ 'RQRWDSSO\WRRPXFKSUHVVXUHRQWKH
PDFKLQH/HWWKHPDFKLQHGRWKHZRUN
Ɣ 6ZLWFKRIIWKHPDFKLQHDQGZDLWIRUWKH
machine to come to a complete standstill
before putting the machine down.
CLEANING AND MAINTENANCE
Before cleaning and maintenance,
always switch off the machine and
remove the mains plug from the mains.
Ɣ 5HJXODUO\FOHDQWKHKRXVLQJZLWKDVRIWFORWK
Ɣ .HHSWKHYHQWLODWLRQVORWVIUHHIURPGXVWDQG
GLUW,IQHFHVVDU\XVHDVRIWPRLVWFORWKWR
remove dust and dirt from the ventilation slots.
Ɣ 5HJXODUO\FOHDQWKHFXWWLQJGLVFVWRDYRLG
inaccuracies during use.
Checking and replacing the carbon brushes
¿J$
7KHFDUERQEUXVKHVPXVWEHFKHFNHGUHJXODUO\,I
the carbon brushes are worn, the machine will
start to run unevenly.
Only use the correct type of carbon
brushes.