Fire-Lite MS-2 - SW2 DIP Switch Configuration Details; Zone Verification and Supervisory Settings

',36ZLWFK6HWWLQJV 3URJUDP2SWLRQVYLD',36ZLWFK
060631% 
3.1.2 SW2 DIP Switch Settings
3.1.2.1 IDC1 Verification (MS-4 only)
6ZLWFKRQO\RQWKH06SODFHGLQWKH21SRVLWLRQVHOHFWVWKH9HULILFDWLRQ
IHDWXUHIRU,'&,QLWLDWLQJ'HYLFH&LUFXLW:KHQ9HULILFDWLRQLVVHOHFWHGWKH
IROORZLQJHYHQWVZLOORFFXUZKHQDVPRNHGHWHFWRUDFWLYDWHV
1. FACP removes power from all zones for 6 seconds, resetting all smoke detectors
2. Power is reapplied and a 12 second retard period begins, allowing detectors to
stabilize
3. During the 18 second reset/retard periods of steps 1 & 2, subsequent alarms by
the same zone are ignored
4. Alarms detected on any other zone during the retard period will cause the FACP
to immediately process the alarm
5. A confirmation period follows the reset/retard period. If an alarm occurs during
the confirmation period, on the zone which initiated verification, the FACP will
immediately process the alarm. If no alarm is detected during this confirmation
period, the FACP returns to normal condition
,PSRUWDQW&LUFXLWVVHOHFWHGIRUYHULILFDWLRQPXVWKDYHRQO\VPRNHGHWHFWRUV
LQVWDOOHG
7KHIDFWRU\GHIDXOWVHWWLQJLVVZLWFK2))IRUQR,'&9HULILFDWLRQ
3.1.2.2 IDC1 Supervisory (MS-4 only)
6ZLWFKRQO\RQWKH06SODFHGLQWKH21SRVLWLRQSURJUDPV,'&DVD
6XSHUYLVRU\FLUFXLW$VXSHUYLVRU\]RQHFDQEHXVHGIRUPRQLWRULQJVXSHUYLVRU\
GHYLFHVVXFKDVVSULQNOHUWDPSHUVZLWFKHV$VXSHUYLVRU\DFWLYDWLRQZLOOSXOVHWKH
SLH]RVRXQGHUDWDòVHFRQGUDWHDQGIODVKWKH]RQHVXSHUYLVRU\/('DWWKHVDPH
UDWH7KHIDFWRU\GHIDXOWVHWWLQJLVVZLWFK2))IRUQR,'&6XSHUYLVRU\
3.1.2.3 IDC1 Verification for MS-2 or IDC2 Verification for MS-4
6ZLWFKSODFHGLQWKH21SRVLWLRQVHOHFWVWKH9HULILFDWLRQIHDWXUHIRU,'&RQ
WKH06RU,'&RQWKH067KHIDFWRU\GHIDXOWVHWWLQJLVVZLWFK2))IRUQR
9HULILFDWLRQ5HIHUWR,'&9HULILFDWLRQ06RQO\IRUDGHVFULSWLRQRIWKLV
IHDWXUH
3.1.2.4 IDC1 Supervisory for MS-2 or IDC2 Supervisory for MS-4
6ZLWFKSODFHGLQWKH21SRVLWLRQSURJUDPV,'&RQWKH06RU,'&RQ
WKH06DVD6XSHUYLVRU\FLUFXLW$VXSHUYLVRU\]RQHFDQEHXVHGIRUPRQLWRULQJ
VXSHUYLVRU\GHYLFHVVXFKDVVSULQNOHUWDPSHUVZLWFKHV$VXSHUYLVRU\DFWLYDWLRQ
ZLOOSXOVHWKHSLH]RVRXQGHUDWDòVHFRQGUDWHDQGIODVKWKH]RQHVXSHUYLVRU\/('
DWWKHVDPHUDWH7KHIDFWRU\GHIDXOWVHWWLQJLVVZLWFK2))IRUQR6XSHUYLVRU\
120 sec.
18 sec.
0 sec.
CONFIRMATION
RETARD
Alarm Ignored
Control Panel Processes Alarm if Same Detector is Still in Alarm
Control Panel Immediately Processes Alarm
Detector Alarm Verification
(Reset/Retard + Confirmation)
Detector Goes Into Alarm
Detector Alarms on Different
Zone During First Detector's
Verification Period
6 sec.
RESET