How to fix a FireAngel Wi-Safe 2 when the green power LED is off?
If the Power (green) LED is not illuminated on your FireAngel Smoke Alarm, check that the power supply is plugged in and switched on at a working power socket.
Why is the amber light on my FireAngel Wi-Safe 2 Smoke Alarm staying on even when the green light is on?
If the power (green) LED is illuminated, but the Fault (amber) LED is continuously lit on your FireAngel Smoke Alarm, it means that the Low Frequency Sounder is not interlinked (“learned in”) to the rest of the network. If this happens regularly after learning in the unit, call Technical Support on 0800 141 2561.
What to do if FireAngel Personal Care Products strobe and vibrating pad does not respond to a smoke or CO alarm test?
First, verify that the alarm, strobe, and vibrating pad have been correctly interlinked. Next, ensure that the units are within the specified range. If the strobe and vibrating pad still don't respond, further assistance may be needed.
Why is the power (green) LED illuminated, and the fault (amber) LED continuously lit on my FireAngel Personal Care Products?
This indicates that the strobe unit is not interlinked with the rest of the network. If you have already interlinked the unit and this issue persists, further assistance may be needed.
What does it mean if the fault (amber) LED double flashes rapidly on FireAngel Personal Care Products?
This indicates that one or more alarms in the network are either missing, faulty, or have been disabled (removed from its base).
What to do if the fault (amber) LED flashes once every 5 seconds continuously on FireAngel Personal Care Products?
Immediately restore mains power to the strobe unit. If the strobe unit has been plugged into the mains and switched on for at least 72 hours, the battery might be defective and require attention.
How to fix FireAngel Personal Care Products when the strobe is connected to power supply but the power (green) LED is not illuminated?
Make sure the power supply is properly plugged into a working power socket and switched on.
What to do if the FireAngel Personal Care Products vibrating pad does not vibrate when testing?
Check that the vibrating pad is correctly connected to the strobe. If it's correctly connected and the fault (amber) LED is flashing after 2 minutes, further assistance may be needed.
What to do if the red LED is continuously showing on my FireAngel Security System?
If the red LED is continuously illuminated on your FireAngel Security System, it indicates that the network is in alarm. You should respond immediately to address the situation.
What to do if the red LED flashes and a buzzer sounds every 60 seconds on my FireAngel Security System?
If the red LED flashes and a buzzer sounds every 60 seconds on your FireAngel Security System, it means the batteries are low and need to be replaced. Replace the batteries to resolve this issue.
Procedure to add a strobe to an existing Wi-Safe 2 network.
Steps to reset the wireless network configuration for Wi-Safe 2 devices.
How to disconnect a strobe from its current wireless network.
How to test the interlinked network via a smoke or CO alarm.
How to test the interlinked network using the strobe unit.
Recommended regular testing schedule for the Wi-Safe 2 network.
Guidance on optimal placement of the vibrating pad for effective use.
Guidance on optimal placement of the strobe unit for visibility.
Describes the device's state when not connected to a network.
Explains the device's operational state when powered but not in alarm.
Details how the strobe and pad function during an actual alarm event.
Functionality to silence alarms and help locate the source during an event.
Essential safety procedures and advice for home fire escape.
Critical actions to take when a carbon monoxide alarm is triggered.
General| Wireless Interconnect | Yes |
|---|---|
| Power Source | Battery |
| Alarm Sound Level | 85 dB at 3 meters |
| Test/Hush Button | Yes |
| Operating Temperature | 0°C to 40°C |
| Sensor Type | Optical |
| Warranty | 10 years |
| Weight | 220g |
| Type | Optical |
| Standards Compliance | EN 14604:2005 |
| Battery Type | Sealed Lithium battery (non-replaceable) |
To Next Page
