Why does my FireAngel Smoke Alarm keep going off for no reason?
Frequent unwanted alarms may be due to the location of your smoke alarm. Also, try cleaning the smoke alarm. If the issue persists, contact technical support for advice.
Why is my FireAngel Thermoptek ST-622 Smoke Alarm chirping intermittently?
Check the location of your smoke alarm. Also, verify that the chirping is definitely coming from your smoke alarm and not another alarm (like a carbon monoxide, burglar, or gas alarm).
What to do if my FireAngel Thermoptek ST-622 goes off when there's no smoke?
Check the location of your smoke alarm. Also, try cleaning the smoke alarm.
What to do if my FireAngel Thermoptek ST-622 doesn't sound during testing?
First, ensure the alarm is fully rotated clockwise on the base plate to activate the power pack. If testing immediately after activation, wait a few seconds for the alarm to settle. Also, make sure you firmly push the center of the test button. If the unit has been silenced and is in low sensitivity mode, it may not test; wait 15 minutes and try again. If the alarm was recently fitted and still fails to self-test, contact technical support.
How to fix a FireAngel Thermoptek ST-622 Smoke Alarm that doesn't sound during testing?
If your FireAngel Smoke Alarm doesn't sound during testing, ensure the alarm is rotated clockwise as far as it can go and is securely located on the mounting plate to activate the power pack. If you've just activated the alarm, wait a few seconds before testing. Also, make sure you firmly push the center of the test button. If the unit has been silenced and is in low sensitivity mode, wait 15 minutes before trying again. If the alarm was recently fitted and still fails to self-test, then no answer.
Combines optical sensing chamber with thermal enhancement for faster response to fire types.
Use in flats/bedsits requires a primary fire detection system for common areas.
Use in individual rooms requires primary system for common areas.
Smoke alarm suitable for use in mobile homes and caravans.
Not intended for non-residential, commercial, or industrial applications.
Avoid bathrooms, kitchens, dusty/dirty areas, draughty areas, insect infested areas, near fluorescent lights.
Diagram shows best ceiling placement and illustrates 'dead air' spaces to avoid.
Alarm levels may be reduced by closed doors, walls, or noise. Not suitable for hearing impaired.
May fail, not sense all fires. Test weekly and replace every 10 years.
Break out mounting plate tabs, mark drill holes, drill and insert anchors.
Fit the mounting plate to the ceiling or wall using the screws provided.
Align lugs on alarm with slots on mounting plate, twist clockwise until fully seated.
Wait 5 seconds after fitting, then test the alarm. Refer to 'Alarm Test' on page 10.
Red LED flashes every 40 seconds to indicate the alarm is active.
Unit emits 'chirp' every 40 seconds. Replace alarm within 7 days.
Temporarily silences low battery chirp for 8 hours. May be repeated up to 10 times.
Test your smoke alarm once every week. Report test failures to Technical Support.
Clean alarm every 3 months using a vacuum cleaner with a soft brush attachment.
Ensure alarm is rotated correctly, test button pressed firmly, or wait if silenced.
Check location and confirm chirping source; rule out other alarms.
Check location, clean the smoke alarm, or check for frequent unwanted alarms.
Low battery warning can only be silenced a max of 10 times. Replace alarm.
Check location, clean alarm, or contact support if issues persist.
If alarm fails, seek manufacturer advice or contact Technical Support.
Proper smoking, match/lighter storage, flammable materials, electrical safety, cooker/fireplace cleaning.
Create floor plan, identify two exits per room, practice drills, recognize signal, teach children safety.
General| Battery Type | Sealed for life lithium battery |
|---|---|
| Power Source | Battery |
| Alarm Sound Level | 85 dB at 3 meters |
| Operating Temperature | 0°C to 40°C |
| Warranty | 10 years |
| Interconnectivity | No |
| Sensor Type | Optical |
| Compliance | EN 14604:2005 |
To Next Page