Flowserve SIHI dry Standard M160

Questions and Answers

K
Katherine AndersonAug 16, 2025
What to do if Flowserve Water Pump shows emergency stop due to mains phase failure?
- J
  jestesAug 16, 2025
  If the Flowserve Water Pump experiences an emergency stop due to mains phase failure, the cause may be a mains phase failure. To resolve this, check the power supply.
C
Crystal GomezAug 19, 2025
What to do if Flowserve Water Pump shows 'DRY - Emergency stop: Deviation control is too high'?
- D
  David CooperAug 19, 2025
  If your Flowserve Water Pump displays 'DRY - Emergency stop: Deviation control is too high', it means the difference in angles between the pump displacer is too significant. To fix this, clean the pump and remove any foreign bodies.
K
Kevin WilliamsAug 21, 2025
What to do if Flowserve Water Pump shows 'DRY - Emergency stop: Drive difference torques is'?
- S
  Shannon RomanAug 22, 2025
  If the Flowserve Water Pump displays 'DRY - Emergency stop: Drive difference torques is', the cause is that the difference in drive torques in the pump displacer is too high. To resolve this, clean the pump and remove any foreign bodies.
C
Charles CochranAug 25, 2025
What to do if Flowserve Water Pump shows 'DRY - Emergency stop: Connection to pump'?
- S
  Sarah BriggsAug 26, 2025
  If your Flowserve Water Pump displays 'DRY - Emergency stop: Connection to pump', it indicates that the pump or device stops because communication is lost. Check the Bus connection wiring (STERLING link PtP) between the main STERLING control module.
A
Adam CarrAug 28, 2025
How to fix angular deviation rate limit too high on Flowserve Water Pump?
- J
  Jim RodriguezAug 28, 2025
  If the Flowserve Water Pump's angular deviation rate limit is too high, it is recommended to clean the pump and remove any foreign bodies.
M
Mathew AlexanderAug 31, 2025
Why Flowserve Water Pump rotates in the reverse direction?
- J
  Jacqueline FinleyAug 31, 2025
  If the Flowserve Water Pump is rotating in the reverse direction, it might be due to an incorrect direction of rotation of the motors caused by external influences. Check the operating behavior of the system to resolve this issue.
J
Jennifer DaySep 3, 2025
What to do if Flowserve Water Pump shows DRY – Sync.Reg System error?
- C
  Carlos RangelSep 3, 2025
  If the Flowserve Water Pump displays 'DRY – Sync.Reg System error', it's due to an internal error. This could be ERROR_FLASH_DATATYPES, ERROR_FLASH_WRITE, ERROR_FLASH_PARASET:MISMAT, or ERROR_UNEXPECTED_MACHINE. Repeat the start-up. Then inform the Service.
J
James WilsonSep 5, 2025
What to do if Flowserve Water Pump shows 'DRY - Error in the free rotation at rotor diagnostics'?
- S
  Scott DicksonSep 5, 2025
  If the Flowserve Water Pump shows 'DRY - Error in the free rotation at rotor diagnostics', the rotor diagnostics might be stopped due to a fault. Repeat the start-up. If necessary, clean the pump. Then inform the service.
U
upayneSep 8, 2025
What to do if Flowserve Water Pump shows 'DRY - Rotation angle too small'?
- J
  Jonathan GarrettSep 9, 2025
  If the Flowserve Water Pump indicates 'DRY - Rotation angle too small', it means the rotor diagnostics are stopped due to a fault. Repeat the start-up. If necessary, clean the pump. Then inform the service.
W
wgarciaSep 12, 2025
How to deactivate boot mode on Flowserve Water Pump?
- P
  psmithSep 12, 2025
  If the Flowserve Water Pump is in boot mode, it is because the drives are in the Boot mode. To resolve this, reset the boot switch.