Fluke 5730A - Page 39

Multifunction Calibrator
Electrical Specifications
29
Range
Frequency
(Hz)
Stability ±1 °C
[1]
24 Hours
Temperature Coefficient
Output Impedance
(Ω)
Maximum
Distortion
Bandwidth 10 Hz-
10 MHz
10 - 40 °C
0 - 10 °C and
40 - 50 °C
±μV ±μV / °C ±(% output + μV)
Load Regulation
±(ppm output + μV)
2.2 V
10 - 20
20 - 40
40 - 20 k
20 k - 50 k
50 k - 100 k
100 k - 300 k
300 k - 500 k
500 k - 1 M
150 + 20
80 + 15
12 + 4
15 + 5
15 + 5
30 + 10
70 + 20
150 + 50
50 + 10
15 + 5
2 + 1
10 + 2
10 + 4
80 + 15
80 + 40
80 + 100
50 + 10
15 + 5
5 + 2
15 + 4
20 + 4
80 + 15
80 + 40
80 + 100
10 + 2
10 + 2
10 + 4
30 + 10
120 + 16
300 ppm
600 ppm
1200 ppm
0.05 + 80
0.035 + 80
0.035 + 80
0.035 + 80
0.035 + 110
0.3 + 110
0.5 + 110
1 + 110
22 V
10 - 20
20 - 40
40 - 20 k
20 k - 50 k
50 k - 100 k
100 k - 300 k
300 k - 500 k
500 k - 1 M
150 + 20
80 + 15
12 + 8
15 + 10
15 + 10
30 + 15
70 + 100
150 + 100
50 + 100
15 + 30
2 + 10
10 + 20
10 + 40
80 + 150
80 + 300
80 + 500
50 + 100
15 + 40
4 + 15
20 + 20
20 + 40
80 + 150
80 + 300
80 + 500
10 + 20
10 + 20
10 + 30
30 + 50
80 + 80
100 + 700
200 + 1100
600 + 3000
0.05 + 700
0.035 + 700
0.035 + 700
0.035 + 700
0.05 + 800
0.3 + 800
0.3 + 800
2 + 800
220 V
10 - 20
20 - 40
40 - 20 k
20 k - 50 k
50 k - 100 k
100 k - 300 k
300 k - 500 k
500 k - 1 M
150 + 200
80 + 150
12 + 80
15 + 100
15 + 100
30 + 400
100 + 10,000
200 + 20,000
50 + 1000
15 + 300
2 + 80
10 + 100
10 + 500
80 + 600
80 + 800
80 + 1000
50 + 1000
15 + 300
4 + 80
20 + 100
20 + 500
80 + 600
80 + 800
80 + 1000
10 + 200
10 + 200
10 + 300
30 + .600
80 + 3,000
250 + 25,000
500 + 50,000
1000 + 110,000
0.05 + 10,000
0.05 + 10,000
0.05 + 10,000
0.05 + 10,000
0.2 + 50,000
1.5 + 50,000
1.5 + 50,000
3.5 + 100,000
±(ppm output + mV) ±(ppm output) / °C ±(ppm output + mV) ±(% output)
1100 V
15 - 50
50 - 1 k
150 + 0.5
20 + 0.5
50
2
50
5
10 + 2
10 + 1
0.15
0.07
1000
100
10
0
3.5 V
10000
50 Hz10 Hz 1 kHz 100 kHz 1 MHz 30 MHz
Voltage
Frequency
40 Hz 30 Hz
2.2 x 10
7
V-Hz
15 Hz
Volt-Hertz Capability
Figure A.