Fluke 700PTP - User Manual

PN 688736
December 1997, Rev.1, 8/02
1997,2002 Fluke Corporation. All rights reserved. Printed in U.S.A.
All product names are trademarks of their respective companies.
Caution
To maintain proper operation of the fine
adjustment knob, never unscrew the fine
adjustment knob past the red line. If you do go
past the red line, vent the pressure from the
system before you re-engage the piston.
Red line indicator
pp03f.eps
8. Tighten the pressure release valve (item .).
9. If you want to limit the maximum pressure that can be
developed by the pump, tighten the maximum-stroke
limiting adjustment nuts (item -). This also reduces
the amount of pressure increase per stroke.
10. To apply very low pressures, use the fine adjustment
knob only (item /).
11. Squeeze the handles together to apply incrementally
higher pressure. For pressure over 7 bar (100 psi),
use two hands.
12. Adjust the pressure using the fine adjustment knob
(item /).
Replacement Parts
Hose assembly, Fluke PN 2029186
Seal kit, Fluke PN 2029173
Handle and main piston assembly, Fluke PN 2029199
Limited Warranty & Limitation of Liability
This Fluke product will be free from defects in material and
workmanship for one year from the date of purchase. This
warranty does not cover fuses, disposable batteries or damage
from accident, neglect, misuse or abnormal conditions of operation
or handling. Resellers are not authorized to extend any other
warranty on Fluke’s behalf. To obtain service during the warranty
period, send your defective calibrator to the nearest Fluke
Authorized Service Center with a description of the problem.
THIS WARRANTY IS YOUR ONLY REMEDY. NO OTHER
WARRANTIES, SUCH AS FITNESS FOR A PARTICULAR
PURPOSE, ARE EXPRESSED OR IMPLIED. FLUKE IS NOT
LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL OR
CONSEQUENTIAL DAMAGES OR LOSSES, ARISING FROM
ANY CAUSE OR THEORY. Since some states or countries do not
allow the exclusion or limitation of an implied warranty or of
incidental or consequential damages, this limitation of liability may
not apply to you.
Fluke Corporation Fluke Europe B.V.
P.O. Box 9090 P.O. Box 1186
Everett, WA 98206-9090 5602 B.D. Eindhoven
U.S.A. The Netherlands
Introduction
The Fluke 700PTP Pneumatic Test Pump (hereafter called
the pump) is a handheld device that develops precise
pressure and vacuum. The pump has the following
specifications:
• Pressure to 40 bar (600 psi)
• Vacuum to -0.96 bar (-13.9 psi)
• Wetted materials: anodized aluminum, brass, nitrile,
and nylon.
• Weight: 1.43 lb (650 g)
• Dimensions: length 8.66 in (220 mm), width 4.13 in
(105 mm), depth 2.48 in (63 mm)
Box Contents
• Model 700PTP Pneumatic Test Pump with hose and
1/4-in. NPT female adapter
• 3/8-in. BSP male to 1/4-in. NPT female adapter
installed in the master instrument port
• Replacement seal kit for the pump
• Instruction Sheet
How to Contact Fluke
To contact Fluke, call one of the following numbers:
USA: 1-888-99-FLUKE (1-888-993-5853)
Canada: 1-800-36-FLUKE (1-800-363-5853)
Europe: +31 402-675-200
Japan: +81-3-3434-0181
Singapore: +65-738-5655
Anywhere in the world: +1-425-446-5500
Visit us on the World Wide Web at:
www.fluke.com
®
Fluke-700PTP
Pneumatic Test Pump
Instruction Sheet

Summary

Introduction and Specifications

Replacement Parts

Limited Warranty and Liability

Contact Information

Test Pump Features

Master Instrument Port

Port for Fluke 700 Series Pressure Module. Supplied with 3/8-in. BSP to 1/4-in. NPT adapter.

Pressure;Vacuum Button

Push in from this side for vacuum, and from the other side for pressure. Use a small screwdriver.

Test Pressure Port Hose

Flexible hose to pressure instrument under test.

Test Pressure Port

1/4-in. NPT adapter.

Maximum Stroke Limiter

Tighten nuts to limit pressure, shortening the compression stroke.

Pressure Release Valve

Unscrew to vent pressure. Tighten valve to close before applying pressure.

Fine Adjustment Knob

Allows precise adjustment of applied pressure.

Using the Test Pump

Connecting Pressure Module

Attach 700 Series Pressure Module to master instrument port.

Connecting Calibrator

Connect pressure module to the calibrator as shown.

Connecting Test Instrument

Connect test pressure port hose to the instrument under test.

Setting Pressure;Vacuum Button

Ensure the pressure/vacuum button is in the desired position.

Venting Pressure

Unscrew the pressure release valve to vent pressure from the pump.

Zeroing Pressure Module

Zero the pressure module according to its specific procedure.

Adjusting Pressure

Turn the fine adjustment knob to mid-range initially.

Fluke 700PTP Specifications

General

Pressure Media	Non-corrosive gases
Pressure Connection	1/4 in NPT female
Materials	Anodized aluminum and stainless steel
Resolution	0.01 psi
Power Supply	Not applicable
Operating Temperature	32 to 122°F (0 to 50°C)
Storage Temperature	-20°C to 60°C
Accuracy	±0.05% full scale