What to do if bibag I2C error appears on Fresenius Medical Care bibag 508213 Medical Equipment?
If there is I2C communication problem, turn machine power off and back on. If the alarm is not cleared, return the blood to the patient if alarm occurs during treatment. Take the machine out of service and alert a qualified service technician.
What to do if there is no bag on bibag connector of Fresenius Medical Care bibag 508213 Medical Equipment?
If there is no bag on the connector, place a bag on the bibag connector and close the door to continue.
What to do if bibag bag leak on Fresenius Medical Care bibag 508213?
If a leak has been detected in the bag, open the bibag door, wait 30 seconds to relieve the pressure, and remove the bag. Place a new bag on the connector and close the bibag door.
What to do if bibag conductivity is high on Fresenius Medical Care Medical Equipment?
If the actual or measured bibag conductivity has exceeded the high conductivity alarm limit when using the bibag disposable, wait five minutes for conductivity to stabilize. If the appropriate conductivity cannot be reached, connect a new bag. If the alarm is still not cleared, return blood to the patient. Take the machine out of service and alert a qualified service technician.
What to do if bicarbonate conductivity is high on Fresenius Medical Care bibag 508213?
If the actual or measured sodium bicarbonate concentrate conductivity has exceeded the high conductivity alarm limit when using the blue bicarbonate connector for liquid bicarbonate, wait five minutes for conductivity to stabilize. If the appropriate conductivity cannot be reached, make sure that the correct bicarbonate source is connected. If the alarm is still not cleared, rinse back the patient’s blood, and disconnect the patient from the machine. Take the machine out of service, and alert a qualified service technician.
What to do if bibag is emptied on Fresenius Medical Care bibag 508213?
If the bibag emptying program has completed, open the bibag door and remove the bag to continue.
What to do if bibag temperature sensor error appears on Fresenius Medical Care bibag 508213?
If the bibag temperature sensor is not reading the correct temperature, insert the blue bicarbonate connector into an appropriate liquid bicarbonate source. Or to use the bibag disposable: If during treatment, rinse back the patient’s blood and disconnect the patient from the machine. Run a Rinse program until message is cleared.
What to do if bibag pressure sensor error appears on Fresenius Medical Care Medical Equipment?
If the bibag connector pressure sensor is experiencing an error, open the bibag door, wait 30 seconds to relieve the pressure, and remove the bag. Place the bag back on the connector and close the door. If the alarm is not cleared, return the blood to the patient if alarm occurs during treatment. Take the machine out of service and alert a qualified service technician.
What to do if bicarbonate venting is too long on Fresenius Medical Care bibag 508213?
If the bibag system has been venting longer than ten minutes when using the blue bicarbonate connector for liquid bicarbonate, press the RESET key to clear the message. If the alarm persists, turn machine power off and back on. If alarm is not cleared, return the blood to the patient if alarm occurs during treatment. Take the machine out of service and alert a qualified service technician.
What to do if bibag pressure is too low on Fresenius Medical Care bibag 508213 Medical Equipment?
If the pressure inside the bibag disposable is below the set alarm limits, open the bibag door, wait 30 seconds to relieve the pressure, and remove the bag. Place the bag back on the connector and close the door. If the alarm is not cleared: * Discontinue use of the bibag system. * Insert the blue bicarbonate connector into an appropriate liquid bicarbonate source in order to continue the treatment. * Alert a qualified service technician.
Monitoring Dialysate| conductivity average accuracy | ± 1.5% |
|---|---|
| conductivity alarm window adjustment at 40 mEq/L | ±0.2 mS/cm |
| conductivity alarm window adjustment at 35 mEq/L | ±0.1 mS/cm |
Operating Environment| standard temperature | 25 °C |
|---|
To Next Page