Frick Vyper 305 - Page 66

VYPER
™
VARIABLE SPEED DRIVE
INDEX
100-200 IOM (FEB 09)
Page 66
Applied Motor FLA, 38, 40
Applied motor FLA, 40
Applied Service Factor, 40
Automanual Switch, 34
Average Current, 33
Baseplate Temperature, 33
Capacity Regulations, 36
Clear Standby Time, 32
Clear VSD Memory, 33
Comm 1, 36
Converter Heatsink Temp, 33
Current Phase, 33
Current Value Timer, 33
DC Bus Voltage, 33
DC Inverter Link Current, 33
fault flags, 34
Filter Current Leg, 33
flydown menu, 31
Full Load Amps, 33
Harmonic Filter screen, 33
High Motor Amps, 39
Home screen, 35
Home Screen Service Level 2, 30
Input Power, 33
Job FLA, 33
Line Frequency Jumper, 34
Low Motor Amps, 38
Manual Speed Switch Status, 33
Modbus Node ID, 34
motor nameplate, 38
Motor Screen, 38
Motor Temperature, 33
motor temperature, 31
Nameplate FLA, 40
No Faults Signal, 34
operational parameters, 31
Output Frequency, 33
Output Voltage, 33
Phase Rotation Direction, 34
PID Setup, 37
Precharge Contactor, 34
Recycle Delay, 38
Run Command Signal, 34
setpoint parameters, 34
Speed Command, 33
Speed Command value, 34
Standby mode, 32
start-up, 34
Supply Contactor, 34
Supply Current, 33
Total Demand Distortion, 33
Total Harmonic Distortion, 33
Total kWh, 33
Vyper™ Level 2 Screen, 47
Vyper™ Level 2 screen, 46
Vyper Amp Limit, 40
Quantum™LX Control panel, 3
Quantum™LX Panel, 54
Quantum™LX panel, 16, 23, 27, 46, 53, 54, 55, 56, 57, 58,
59
R
Rate of Decrease, 41
Rate of Decrease Delay Time, 41
Rate of Increase, 41
Rate of Increase Delay Time, 41
RFI, 11, 12, 20, 27
RMS, 50
RMS input, 59
RMS output, 59
running coolant, 27
S
saturation voltage, 54
SCR, 12, 51, 54, 56, 57
SCR/Diode block, 56
screw compressor, 7
SCR trigger, 51
SCR Trigger Control, 54
Serial Communications, 52
Serial data, 52
Serial Number, 3
shipping coolant, 27
slide valve, 42, 44
Slide Valve, 41, 45
Solid-state, 11
start-up, 34, 42, 50
Status data, 56
Stop Load, 16
SW1 switch, 52
T
T1 lug, 50
temperature sensor, 12, 55
temperature sensors, 20, 27
test button, 51
thermistors, 23
thermistor sensor, 55
THREE-PHASE INDUCTOR, 14
timeout, 60
Total Demand Distortion, 53
Total Harmonic Distortion, 7
transformer, 7
TRANSFORMERS, 11
transformer voltage, 7
trigger board, 57
trim pot, 46, 54
Trim Pot Adjustment, 28
V
VSD fault, 51
VSD memory, 32
Vyper Pre-Installation Site Check List, 5
Vyper Pre-Operation Site Check List, 5
Vyper™ Logic board, 52, 53, 56, 57
W
water pump, 55
Water Recommendations, 8