– 20 –
12-2
PXG5/9 Motorized Valve Control Model List
Note 1: If front panel size 48 × 96, the transmitter power supply output is not available.
13
Specifications
Digit
Specifications 1 2 3 4 5 6 7 8 - 9
10 11 12 13
-
14
Notes
4 <Size of front WxH>
48 x 96 mm P X G 5
Note 1
96 x 96 mm P X G 9
5 <Output 1>
Motor valve control output
(no PFB input)
S
Motor valve control output
(PFB input)
V
6 <Output 2>
None Y
Auxual DO output A
Transmitter power supply T
Note 1
7 <Option 1>
None Y
Digital input (No. 1, 2, 3) + RSV1 E
RS 485 + digital input (No. 1, 2, 3) U
RS 485 + digital input
(No. 1) + RSV1
F
8 <Revision symbols> 1
9
<Digital Output> (Relay contact output)
None 0
Digital output 1 point (No.1) 1
Digital output 2 points (No.1, 2) F
Digital output 3 points (No.1, 2, 3) M
Digital output 2 points
[independent common] (No.1, 2)
J
10
<Power Supply> <Instruction Manual>
100V/240V AC no instruction manual
N
100V/240V AC English instruction manual
V
24V AC/DC no instruction manual C
24V AC/DC English instruction manual
B
11 <Option 2>
None Y
12 0
13 0
Power Supply 100 (-15%) to 240V AC (+10%), 50/60dHz, 24V DC/AC (±10%)
Power Consumption 12VA or less
Control Output
Relay contact output
•1a contact 220V AC / 30V DC , 3A (resistance load)
SSR/SSC drive output (voltage pulse output)
•ON 20V DC (18 to 24V DC)
•OFF 0.5V DC or less
•Max Current 20mA DC or less (both OUT1 and OUT2)
•Load resistance 850Ω or more
Current Output
•0 to 20mA DC / 4 to 20mA DC
•Acceptable load resistance 600Ω or less
•Accuracy: ±5%FS
Voltage output
•0 to 5V DC / 1 to 5V DC / 0 to 10V DC / 2 to 10V DC
•Resistance load 10kΩ or more
•Accuracy: ±5%FS
Process value input
Input accuracy
•
Thermocouple input: greatest one among ±0.3%FS, ±1
digit, and ±1°C or 2°C
• Resistance bulb input: greatest one among ±0.3%FS, ±1
digit, and ±0.5°C
• mV input, voltage input, current input : ±0.3%FS±1digit
Indication resolution: ±0.3%FS or less
Digital Output
Relay contact output
(DO1 to DO3)
•1a contact 220V AC / 30V DC , 3A (resistance load)
Transistor Output (DO4, DO5)
•Open collector 30V DC, 100mA, max 2 contacts
•Judged ON 1V DC or less
Digital input
Contact or Transistor type
Max 5 inputs 30V DC, 3mA (1 input)
•Judged ON 1kΩ or less (contact), or 5V DC or less (transistor)
•Judged OFF
100kΩ or more (contact), or 18V DC or more (transistor)
Re-transmission output
0 to 20mA DC / 4 to 20mA DC / 0 to 5V DC / 1 to 5V DC /
0 to 10V DC / 2 to 10V DC
Re-transmission data: PV, SV, DV, MV
Accuracy: ±0.2%FS
Resistance load : 600Ω or less (Current), 10kΩ or more (voltage)
Remote SV Input
1 to 5V DC /0 to 5V DC, 0 to 20mA DC / 4 to 20mA DC (use an
external 250Ω resistor)
Heater break detector (CT)
input
Single-phase type CT 1 input, 1 to 30A / 20 to 50A
Valve feedback signal
(potentiometer) input
Resistance range: 100 to 2.5k
Ω (three line type)
Resolution: 0.5% FS
Input accuracy: ±1.0% FS
Corresponding full stroke time: 30 sec to 180 sec
Motorized valve control
output
1a contact x 2, 220V AC / 30V DC , 3A (resistance load)
Transmitter supply power
input
24V DC (19.5 to 24V DC), max current 21.6mA (with short-circuit
protection)
Max load resistance: 400Ω
Communication Functions
RS-485 interface
Communication method: Half-duplex bit serial asynchronous cycle
Communication rate: 9600bps, 19200 bps
Protocol: Modbus RTU compatible
Communication distance: Max 500m (total connection length)
Connectable units: 31 units
Loader Interface
RS-232C interface
Connection method: ø2.5 mini-plug/jack (use the included cable at
the bottom of the case)
Communication method: Full-duplex bit serial asynchronous cycle
Communication speed: 9600bps parity/none
Protocol: Modbus RTU compatible
Operation and storage
conditions
Range of usable temperatures: -10 to 50°C, ambient humidity 90%
RH or less (non condensing)
-20 to 60 °C (storage temperature)
To Previous Page
Loading...
