Fuji Electric ZKJ Series - Page 81

6 - 41
6.9 Manual calibration procedure
6.9.1 Manual zero calibration
It is used for zero point adjustment. For
zero calibration gas, suited for an application
VKRXOGEHXVHGDFFRUGLQJWR³6WDQGDUGJDV
LQ6HFWLRQ6DPSOLQJ´
(1) Press the
ZERO
NH\RQWKH0HDVXUHPHQW
VFUHHQWRGLVSOD\WKH0DQXDO=HUR&DOL-
bration screen.
 6HOHFWWKH&KFRPSRQHQWWREHFDOLEUDW-
ed by pressing the
or key. After
selection, press the
ENT
key, and zero gas
will be supplied.
 :DLWXQWLOWKHLQGLFDWLRQLVVWDELOL]HGZLWK
the zero gas supplied. After the indica-
tion has been stabilized, press the
ENT
NH\=HURFDOLEUDWLRQLQUDQJHVHOHFWHGE\
the cursor is carried out.
Note: For the Ch (component) for
which “AR” is selected in “6.1.1
Setting range switch mode,” the
cursor automatically moves to
the range selected in “Setting
of auto calibration component/
range” (6.2.4), and calibration is
carried out within that range.
ENT
( )
ENT
To Measurement screen after ex-
ecuting Manual Zero Calibration
・ The analyzer simultaneously calibrate the zero
point of all the channels (components) that have
been set to “at once” in “6.2.2 setting of manual
zero calibration”.
・ The analyzer simultaneously calibrate the zero
points of both ranges of the channels
(components) set to “both” in “6.2.3 setting of
calibration range”.
CAUTION
To close the “Zero Calibration” or
cancel this mode midway, press the
key. A previous screen will return.
To close "Zero Calibration"
ESC
ZERO
Measurement Mode
0
0 0
0
0
0
ZERO Cal.
• Chl
NOx
• Ch2
S02
• Ch3
CO2
• Ch4
co
• Ch5
02
ZERO Cal.
• Chl
NOx
• Ch2
S02
• Ch3
CO2
• Ch4
co
• Ch5
02
ZERO Cal.
Chl
NOx
Ch2
S02
Ch3
CO2
Ch4
co
Ch5
02
II
Select Ch No.
with UP / DOWN and ENT
Back with ESC
• Range 1 0-100
ppm
00
Ranqe2 0-2000 oom
• Rangel 0-100
ppm
00
Ranqe2 0-2000 oom
• Rangel 0-10
vol%
000
Ranqe2 0-20
vol%
• Rangel 0-100
ppm
00
Ranqe2 0-2000 oom
Rangel 0-10
vol%
• Ranqe2 0-25
vol% 2009
Select Ch No.
with UP / DOWN and ENT
Back with ESC
• Rangel 0-100
ppm
00
Ranqe2 0-2000 ppm
• Rangel 0-100
ppm
00
Ranqe2 0-2000 oom
• Rangel 0-10
vol%
000
Ranqe2 0-20
vol%
• Rangel 0-100
ppm
00
Ranqe2 0-2000 oom
Rangel 0-10
vol%
• Ranqe2 0-25
vol% 2009
ENT : Go on calibration
of selected Ch.
ESC : Not calibration
• Rangel 0-100
ppm
Ranqe2 0-2000 ppm
[J
00
• Rangel 0-100
ppm
Ranqe2 0-2000 ppm
[J 09
• Rangel 0-10
vol%
[J
0.34
Ranqe2 0-20
VO l %
• Rangel 0-100
ppm
Ranqe2 0-2000 ppm
[J
1. 1
Rangel 0-10
vol%
• Ranqe2 0-25
vol%
[J
2009
II