Fujitsu AOTG30LATL User Manual

En-18
(2) Select the pattern number with the [Cursor button (Up/
Down)]. Then press the [Cursor button (Right)] to set
the time setting of On/Off timer, On/Off, operating mode,
and temperature for the current selected pattern.
1
Weekly
1
Day
Time
End
Su Mo
Weekly timer setting
Time 8
Time 2
Mo 10:00
Delete: Push for two seconds
OK:
NOTE
• Todeletethesetting,movethecursortothepattern
number, and press the [Cancel button] for 2 seconds.
(3) Adjust time setting of On/Off timer with the [Cursor but-
ton (Up/Down)].
1
Weekly
1
Day
Time
End
Su Mo
5 00
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
(4) Select [On] (On timer) or [Off] (Off timer) with the [Cursor
button (Up/Down)].
When you selected [Off] (Off timer), the necessary set-
ting for this pattern is completed here. If you continue
to set other pattern, press the [Cursor button (Right)].
If you complete all of the setting on timer conditions for
each pattern here, proceed to step 6.
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
(5) When you selected [On] (On timer), select the operating
mode with the [Cursor button (Up/Down)].
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
°
C
(6) When you selected [On] (On timer), adjust the value to
the desired temperature with the [Cursor button (Up/
Down)].
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
20
°
C
NOTES
• Possible temperature setting ranges in the operation mode
areasfollows:
Cool, Dry, Auto ................ 18to30°C(64to88°F)
Heat ................................. 16to30°C(60to88°F)
• If the temperature out of the Set temp. range limitation is
set, it will be reset at the nearest temperature within the
range. However, the adjusted temperature value in this
setting will not be corrected automatically.
(7) Select [Zone (single)] (individual setting of zone control)
or [Zone (group)] (simultaneous setting of zone control)
asfollows:
Individual setting of zone control:
Select [Zone (single)] with the [Cursor button (Up/
Down)]. Then press the [Cursor button (Right)] to move
the cursor to next setting item.
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
20
°
C
Zone
(
sin
g
le
)
Sensor:
Select the room-temperature sensor with the [Cur-
sor button (Up/Down)]. Then press the [Cursor button
(Right)] to move the cursor to next setting item.
1
Weekly
1
Day
Time
End
Su Mo
5 00
On
Weekly timer setting
Time 8
Time 2
Mo 10:00
Cancel:
OK:
Heat
20
°
C
Zone
(
sin
g
le
)
Sensor
Zone 1
Secondar
y
RC
Zone 2
Zone 3 Zone 4
Zone 5 Zone 6
Zone 7 Zone 8
9381067145_OM_EN.indd 18 14/09/2015 13:48:04

Fujitsu AOTG30LATL Specifications

General

Brand	Fujitsu
Model	AOTG30LATL
Category	Air Conditioner
Language	English