Fujitsu FI-5530C2 Installation Procedures

Fujitsu SCSI Scanner Installation Procedures
Windows 95\98\98SE\ME\2000\XP\Vista
Rev082708A Page 1 of 1
If you are installing the following models by means of the SCSI interface then please use this
document.
Fi-5530C2 Fi-6140 Fi-6670\A
Fi-6240 Fi-6770\A
Hardware requirements.
You will need a PC system that meets our recommended specifications, an appropriate SCSI
controller, and a SCSI cable (six foot recommended maximum). For recommended PC system
specifications and SCSI controllers please reference the Scanner Hardware Reference
page.
You may also need your Operating System Disk.
Step A: Installing the SCSI Host Adapter (Adaptec).
1. Shut down your PC and remove the case cover.
2. Locate a free PCI slot and remove the back plate if necessary.
3. Install the SCSI controller in an open PCI slot.
Make sure that the card is seated completely in the slot and secured in the frame
Warning! Failure to secure the SCSI controller in the PC can result in damage to the
SCSI card, scanner, and/or your system.
4. Boot your PC without the scanner attached
.
Step B: Installing the SCSI drivers (Adaptec).
5. When the New Hardware wizard comes up, allow Windows to finish installing the
hardware files for the SCSI controller.
6. Then either install/update the ASPI drivers from the CD or go to www.adaptec.com
,
and click on the “search” tab.
7. For Windows 95\98 or ME scroll down to the “Enter key word or quoted phrase” box
and type in “aspi32”.
8. Next scroll down to the drivers section, click on ASPI32 and follow the prompts to
download it your desktop or a new folder.
9. Afterwards go to that location and double click on the "aspi32.exe" icon and follow
the prompts.
10. When the message “ASPI is up to date” appears, reboot and go to the next step.
11. For Windows 2000 or XP scroll down to the “Enter key word or quoted phrase” box
and type in “aspi”.
12. Next scroll down to the drivers section, click on ASPI_v470 or higher and follow the
prompts to download it.
13. Afterwards go to that folder and unzip the file to the default Adaptec\ASPI folder.
14. Then go to start, run, browse to the Adaptec\ASPI folder, select ASPIINST.EXE and
run it.
15. When the message “ASPI is up to date” appears, reboot and go to the next step.

Fujitsu FI-5530C2 Specifications

General

Film scanning	No
Color scanning	Yes
Grayscale levels	256
Input color depth	- bit
Maximum scan size	297.18 x 431.8 mm
Scanner type	Sheet-fed scanner
Sensor type	CCD
Internal memory	64 MB
Maximum duty cycle	120000 pages per month
ISO A-series sizes (A0...A9)	A4
Auto document feeder (ADF) input capacity	100 sheets
Bundled software	Kofax VRS Professional, ScandAll Pro, Adobe Acrobat Standard
Compatible operating systems	Microsoft Windows 2000 Professional / Microsoft Windows XP / Microsoft Windows Server 2003 / Microsoft Windows Vista
Minimum scan size	2.1 x 2.9\
Power requirements	100-240 VAC, 50/60 Hz
Maximum scan area (ADF) (imperial)	11.7 x 17 \
Minimum scan area (Auto Document Feeder)	2.1 x 2.9 \
Sustainability certificates	ENERGY STAR
Power consumption (standby)	12 W
Power consumption (typical)	57 W
Operating temperature (T-T)	5 - 35 °C
Operating relative humidity (H-H)	20 - 80 %

Weight and Dimensions

Depth	228.6 mm
Width	406.4 mm
Height	292.1 mm
Weight	8482.17 g