Fujitsu MHV2100AH - Page 272

Index
IN-4 C141-E217
power-on sequence ....................................4-6
programmable filter circuit......................4-10
protocol for command abort ..................5-131
protocol for the command execution
without data transfer...........................5-135
R
raw attribute value ...................................5-48
READ BUFFER ......................................5-73
read circuit...............................................4-10
READ DMA............................................5-69
READ DMA (EXT).................................6-12
READ DMA EXT .................................5-111
READ DMA EXT ...................................6-12
READ LOG EXT ..................................5-114
READ MULTIPLE..................................5-63
READ MULTIPLE (EXT) ......................6-12
READ MULTIPLE EXT..............5-113, 6-12
READ NATIVE MAX ADDRESS.......5-103
READ NATIVE MAX ADDRESS
EXT....................................................5-112
READ SECTOR(S) .................................5-21
READ SECTOR(S) (EXT)......................6-12
READ SECTOR(S) COMMAND
protocol..............................................5-130
READ SECTOR(S) EXT .............5-110, 6-12
READ VERIFY SECTOR(S)..................5-26
READ VERIFY SECTOR(S) EXT.......5-124
read/write circuit......................... 2-3, 4-3, 4-9
read/write circuit block diagram................4-9
read/write preamplifier (PreAMP).............4-9
read-ahead cache......................................6-12
read-ahead cache system............................1-3
RECALIBRATE......................................5-20
recommended series termination for
ultra DMA..........................................5-148
reliability..................................................1-10
reset............................................................6-8
reset response...........................................6-20
response to
diagnostic command ..............................6-6
hardware reset.................................6-3, 6-4
power-on .........................................6-2, 6-3
software reset .........................................6-5
ripple..........................................................1-6
S
sector count register...................................5-9
sector number register..............................5-10
sector slip processing...............................6-10
SECURITY DISABLE PASSWORD...5-101
SECURITY ERASE PREPARE..............5-97
SECURITY ERASE UNIT......................5-98
SECURITY FREEZE LOCK...................5-99
SECURITY SET PASSWORD ...............5-93
SECURITY UNLOCK ............................5-95
SEEK........................................................5-27
seek operation ..........................................4-18
selective self-test feature flag...................5-57
selective self-test log data structure .........5-56
selective self-test pending time................5-57
self-calibration ...........................................4-7
self-calibration content...............................4-7
self-diagnosis .............................................1-3
self-test execution status ................ 5-49, 5-55
self-test index...........................................5-55
self-test number........................................5-55
sensing and compensating for
external force..........................................4-7
sequential hit............................................6-16
series termination required for ultra
DMA...................................................5-148
service area.................................................3-7
service life................................................1-10
servo burst capture circuit........................4-13
servo circuit................................................4-3
servo control.............................................4-12
servo control circuit .................................4-12
servo frame format...................................4-17
servo mark................................................4-17
SET FEATURES .............................5-89, 6-9
SET MAX..............................................5-104
SET MAX ADDRESS...........................5-104
SET MAX ADDRESS EXT ..................5-118
SET MAX FREEZE LOCK...................5-108
SET MAX LOCK ..................................5-106
SET MAX SET PASSWORD ...............5-105
SET MAX UNLOCK.............................5-107
SET MULTIPLE MODE.........................5-67
shock and vibration....................................1-9
shock and vibration specification...............1-9
signal assignment on the connector............5-3
SLEEP.............................................. 5-40, 6-9
sleep mode..................................................6-8
SMART....................................................5-41
SMART error logging..............................5-52
SMART self-test......................................5-55
SMART self-test log data format.............5-55
spare area....................................................6-9
specification...............................................1-4
specification summary ...............................1-4
spindle........................................................4-2
spindle motor..............................................2-2
spindle motor control ...............................4-19
spindle motor control circuit....................4-13
spindle motor driver circuit........................4-3
stable rotation mode.................................4-19