To Next PageTo Next PageWhy does the Fujitsu ScanSnap S300 Scanner create same file size for black and white and color images?
If your Fujitsu Scanner produces the same file size for both black & white and color images, it's likely that the B&W document was scanned in color mode. To fix this, select [B&W] from the [Color mode] drop-down list on the [Scanning] tab in the [ScanSnap Manager D Scan and Save Settings] dialog box.
Why is my Fujitsu Scanner not recognized after installing ScanSnap Manager?
If your Fujitsu Scanner isn't recognized even after installing ScanSnap Manager, it might be because the scanner was connected to your PC before the software installation. Check Device Manager to see if the scanner is listed as 'Other device' or 'Unknown Device.' If so, delete the device name (such as USB device) under the 'Other Device' section in Device Manager and then restart your PC.
How to fix vertical lines in scanned images with Fujitsu ScanSnap S300 Scanner?
If you notice vertical lines appearing in the scanned images from your Fujitsu Scanner, the inside of the ADF may be dirty. Clean the inside of the ADF.
How to fix multi-feed errors on Fujitsu ScanSnap S300?
To address frequent multi-feed errors on your Fujitsu Scanner, start by cleaning the Pad ASSY. If cleaning doesn't resolve the issue, the Pad ASSY may be worn and require replacement. Also, ensure the document stack is not thicker than 1 mm; reduce the number of sheets if necessary.
What to do if scanning does not start on my Fujitsu Scanner?
If scanning doesn't start on your Fujitsu Scanner, make sure ScanSnap Manager for the ScanSnap S300 is installed. Also, ensure the USB cable is correctly connected, paying attention to the hub's power supply if one is in use. When using a USB bus power cable, use a powered USB hub equipped with an AC adapter. Try disconnecting and then reconnecting the power or USB bus power cable, waiting at least 5 seconds before reconnecting.
What to do if my Fujitsu Scanner is scanning too slowly?
If your Fujitsu Scanner is running slowly, first check if your PC meets the recommended system requirements. If not, at [Scanning] D [Option] in the [ScanSnap Manager D Scan and Save Settings] dialog box, clear the checkboxes of the following to increase the scanning speed: Correct skewed character strings automatically, Allow automatic image rotation. Also, ensure you're not using a USB 1.1 connection; if your PC has a USB 2.0 port, connect the scanner to it, ensuring any USB hub also supports USB 2.0.
What to do if Fujitsu Scanner scanning does not start?
If your Fujitsu Scanner isn't starting the scanning process, first, ensure that ScanSnap Manager for the ScanSnap S300 is installed. Connect the USB cable correctly, checking the hub's power supply if you're using one, and use a powered USB hub with an AC adapter if using a USB bus power cable. Try disconnecting and reconnecting the power or USB bus power cable, waiting at least 5 seconds before reconnecting. If scanning after resuming from hibernation, move the mouse or press a key beforehand. Also, confirm that ScanSnap Manager is running; if the icon isn't displayed, start it from the Start menu.
Why does Fujitsu ScanSnap S300 Scanner produce black lines on scanned documents?
Black lines may appear on documents scanned with your Fujitsu Scanner if the document was written with a pencil. This can make the rollers dirty or cause improper paper feeding. Clean the rollers frequently.
Why are images unreadable from my Fujitsu ScanSnap S300 Scanner?
If the scanned images from your Fujitsu Scanner are unreadable, especially with small letters, right-click the ScanSnap Manager icon on the taskbar and select [Best] or [Excellent] in the [Scanning] tab and scan them again. Note that scanning in [Excellent] mode takes longer and enlarges the image data size.
How to correct skewed images with Fujitsu ScanSnap S300 Scanner?
If scanned images from your Fujitsu Scanner are skewed, and the documents are fed into the ADF with a skew of more than +/-5 degrees, load the document onto the scanner so that the document skew does not exceed this limit. The [Correct skewed character strings automatically] function can correct skewed images up to +/-5 degrees.
General| Film scanning | No |
|---|---|
| Color scanning | Yes |
| Input color depth | - bit |
| Maximum scan size | 216 x 360 mm |
| Scanner type | Sheet-fed scanner |
| Sensor type | CIS |
| Minimum scan area (ADF) | 50.8 x 50.8 mm |
| ISO A-series sizes (A0...A9) | A4, A5, A6 |
| ISO B-series sizes (B0...B9) | B5, B6 |
| Maximum ISO A-series paper size | A4 |
| Auto document feeder (ADF) input capacity | 10 sheets |
| Bundled software | ScanSnap Manager V4.2, ScanSnap Organizer V3.2, CardMinder V3.2 |
| Scan media weight | 64 - 104.7 g/m² |
| Dimensions (WxDxH) | 284 x 95 x 77 mm |
| Power requirements | AC 100V to 240V, 50 / 60 Hz |
| Dimensions (W x D x H) (imperial) | 11.18 x 3.74 x 3.03 \ |
| Maximum scan area (ADF) (imperial) | 8.5 x 14.17 \ |
| Minimum scan area (Auto Document Feeder) | 2 x 2 \ |
| Minimum RAM | 512 MB |
| Minimum storage drive space | 920 MB |
| Compatible operating systems | Windows 2000 Professional, Windows XP, Windows Vista |
| Power supply type | AC/USB |
| Power consumption (standby) | 5 W |
| Power consumption (typical) | 9 W |
| Sustainability certificates | ENERGY STAR |
| Operating temperature (T-T) | 5 - 35 °C |
| Operating relative humidity (H-H) | 20 - 80 % |
| Certification | RoHS |
Weight and Dimensions| Weight | 1400 g |
|---|
