Fujitsu UTY-RNRGZ1 - FAN CONTROL FOR ENERGY SAVING

(5) Touch the [Absence Detection Time] on the “Auto Sav-
ing” screen.
(6) The “Absence Detection Time” screen is displayed. Set
the time with [
] or [ ]. The time can be set to 15, 30,
45, 60, 90, 120 or 180 min.
(5) (6)
Auto Saving
Cancel OK
Enable/Disable [Disable]
Absence Detection Time [In 30 min.]
Fri 10:00AM
Absence Detection Time
Cancel OK
In
min.
30
Fri 10:00AM
Note
When detection time the same as or longer than “Auto
Off” is set at “Auto Saving”, “Auto Saving” does not oper-
ate.
When the [OK] is touched, the display returns to the “Auto
Saving” screen. And when the [OK] on the “Auto Sav-
ing” screen is touched, the display returns to the “Human
Sensor Setting” screen.
Setting of the Auto Off
(7) Touch the [Auto Off] on the “Human Sensor Setting”
screen. “Auto Off” screen is displayed. Touch the [En-
able/Disable] on the “Auto Off” screen.
(8) “Enable/Disable” screen is displayed. Touch the [Enable]
on the “Enable/Disable” screen.
(7) (8)
Auto Off
Cancel OK
Enable/Disable [Disable]
Absence Detection Time [In 24 hr]
Fri 10:00AM
Enable/Disable
Cancel OK
Enable
Disable
When the [OK] is touched, the display returns to “Auto
Off” screen.
(9) Touch the [Absence Detection Time] on the “Auto Off”
screen.
(10) The “Absence Detection Time” screen is displayed. Set
the time with [
] or [ ]. The time can be set from 1 to
24 hr.
(9) (10)
Auto Off
Cancel OK
Enable/Disable [Disable]
Absence Detection Time [In 24 hr]
Fri 10:00AM
Absence Detection Time
Cancel OK
In
hr
24
Fri 10:00AM
Note
When detection time the same as or shorter than “Auto
Saving” is set at “Auto Off”, “Auto Saving” does not oper-
ate.
When the [OK] is touched, the display returns to the “Auto
Off” screen. And when the [OK] on the “Auto Off” screen
is touched, the display returns to the “Human Sensor
Setting” screen.
When the [Back] on the “Human Sensor Setting” is
touched, the display returns to the “Special Setting”
screen.
3-5-6 Fan Control for Energy Saving
(for administrator)
(1) Touch the [Fan Control for Energy Saving] on the “Spe-
cial Setting” screen. When the “Password Verication”
screen is displayed, enter the password and touch the
[OK].
(2) “Fan Control for Energy Saving” screen is displayed.
Touch the [Enable] on the “Fan Control for Energy Sav-
ing” screen.
(1) (2)
Back
Previous
Page
Page 2/ 2 Special Setting
Human Sensor
Setting
Fan Control for
Energy Saving
Fan Control for Energy Saving
Cancel OK
Enable
Disable
When the [OK] is touched, the display returns to the
“Special Setting” screen.
3-6 Summer Time (Daylight Saving Time)
Setting (for administrator)
The time display and timer operation are 1 hour earlier than
usual.
(1) Touch the [Summer Time
Setting] on the “Main Menu”
screen.
Monitor
Previous
Page
Page 2/ 2 Main Menu
Summer Time
Setting
Initial Setting Maintenance
Preference
Enable or Disable the Summer Time Setting
(1) “Summer Time Setting” screen
is displayed. Select the [En-
able] or [Disable] on the “Sum-
mer Time Setting” screen.
Summer Time Setting
Cancel OK
Enable
Disable
When the [OK] is touched, after the setting change
screen is displayed, the display returns to the “Main
Menu” screen.
3-7 Preference (for administrator)
Settings of the Touch Panel Display
(1) Touch the [Preference] on the “Main Menu” screen.
(2) “Preference” screen is displayed.
(1) (2)
Monitor
Previous
Page
Page 2/ 2 Main Menu
Summer Time
Setting
Initial Setting Maintenance
Preference
Back
Preference
Panel
Calibration
Backlight
Setting
Contrast
The following contents are set:
• Panel Calibration:
When the touched position and the corresponding
position does not match on the screen, perform this
setting.
• Backlight Setting:
Backlight enable/disable, brightness, and off time can
be set.
• Contrast:
Adjusts the contrast of the screen.
En-15
En-16