Fujitsu UTY-RNRT - Initial Setting (for administrator)

3-8-2 Backlight Setting
(1) Touch the [Backlight Setting]
on the “Preference” screen.
Back
Preference
Panel
Calibration
Backlight
Setting
Contrast
Enable or disable the backlight
(2) “Backlight Setting” screen is displayed. Touch the [En-
able/Disable] on the “Backlight Setting” screen.
(3) “Enable/Disable” screen is displayed. Select the [Enable]
or [Disable].
(2) (3)
Enable/Disable [Enable]
[30s]
[2]
Automatic Off Time
Brightness
Backlight Setting
Cancel OK
Enable/Disable
Cancel OK
Enable
Disable
When the [OK] is touched, the display returns to the
“Backlight Setting” screen.
NOTE
When set to “Disable”, [Automatic Off Time] and
[Brightness] setting are unnecessary.
(Cannot be
set) Go to (8).
Set the time until backlight is turned off .
(4) Touch the [Automatic Off Time] on the “Backlight Set-
ting” screen.
(5) “Automatic Off Time” screen is displayed. Select the [60
sec.] or [30 sec.].
(4) (5)
Enable/Disable [Enable]
[30s]
[2]
Automatic Off Time
Brightness
Backlight Setting
Cancel OK
Automatic Off Time
Cancel OK
30s
60s
When the [OK] is touched, the display returns to the
“Backlight Setting” screen.
Adjust the brightness of Backlight
(6) Touch the [Brightness] on the “Backlight Setting” screen.
(7) “Brightness” screen is displayed. Adjust the brightness
with the [
] or [ ].
(6) (7)
Enable/Disable [Enable]
[30s]
[2]
Automatic Off Time
Brightness
Backlight Setting
Cancel OK
2
3
1
Brightness
Cancel OK
Brightness
Cancel OK
When the [OK] is touched, the display returns to the
“Backlight Setting” screen.
Apply the setting.
(8) After setting is complete,
touch the [OK] on the “Back-
light Setting” screen.
After the setting change is
displayed, the display returns
to the “Preference” screen.
Enable/Disable [Enable]
[30s]
[2]
Automatic Off Time
Brightness
Backlight Setting
Cancel OK
3-8-3 Contrast Setting
(1) Touch the [Contrast Setting] on the “Preference” screen.
(2) “Contrast Setting” screen is displayed. Adjust the con-
trast with [
] or [ ].
(1) (2)
Back
Preference
Panel
Calibration
Backlight
Setting
Contrast
2
3
4
5
1
Contrast
Cancel OK
When the [OK] is touched, after the setting change
screen is displayed, the display returns to the “Prefer-
ence” screen.
3-9 Initial Setting (for administrator)
Perform this setting at installation. The setting can also be
changed after installation.
(1) Touch the [Initial Setting] on the “Main Menu” screen.
(2) When “Password Verifi cation” screen is displayed, enter
the Password (or Installer Password) and touch [OK].
(1) (2)
Monitor
Previous
Page
Page 2/ 3 Main Menu
Summer Time
Setting
Initial SettingPreference
Special Setting
Next
Page
0
CL
5
1
6
2
7
3
8
4
9
Cancel OK
Password Verification
Enter Current Password
(3) If the password is entered correctly, the “Initial Setting”
screen is displayed. The screen has 3 pages which are
switched by touching the [Next Page] or [Previous Page].
Back
Next
Page
Page 1/ 3 Initial Setting
Date Setting
R.C.Group
Name Setting
Temp. Unit
Setting
R.C. Sensor
Setting
Back
Previous
Page
Page 2/ 3 Initial Setting
Password Setting
Display Item
Setting
Master Indoor
Unit Setting
Next
Page
RC Master/
Slave Setting
Back
Previous
Page
Page 3/ 3 Initial Setting
Zone Setting
I.U. Display
Number Setting
The following contents are set. (♦: for installer)
(*1: Items that indoor unit does not support are not dis-
played.)
(*2: Items are not displayed, if not connected to the zone
interface.)
• Date Setting:
The date and time display format are set. When the
power is turned off , the date and time data hold time
by built-in battery is approximately 7 days. When the
power is turned off for longer than this, the date and
time must be reset.
• Temp. Unit Setting:
The temperature display unit is switched to “°C” or “°F”.
Factory settings is “°C”.
• R.C.Group Name Setting:
The remote controller group name can be set or
changed.
En-18
9373329831-02OMEnUTY-RNRT.indd189373329831-02OMEnUTY-RNRT.indd18 2021/11/1913:23:032021/11/1913:23:03