Fujitsu UTY-RNRT - Temp. Unit Setting; R.C.group Name Setting; Sensor Setting; Password Setting

(12) “Time Format” screen is
displayed. Select the desired
format.
When the [OK] is touched, the
display returns to the “Display
Format Setting” screen.
00:00–11:59 AM/PM
00:00–23:59
Time Format
Cancel OK
12:00–11:59 AM/PM
Fri 10:00AM
(13) When the [OK] on the “Display Format Setting” screen
is touched, after a setting change screen is displayed,
the display returns to the “Date setting” screen.
Quit the Date setting
(14) When the [Back] on the “Date
Setting” screen is touched, the
display returns to the “Initial
Setting” screen.
Date Setting
Date and Time Setting
Display Format Setting
Back
3-9-2 Temp. Unit Setting
(1) Touch the [Temp. Unit Setting] on the “Initial Setting”
screen.
(2) “Temp. Unit Setting” screen is displayed. Select the [°C]
or [°F]. (Factory setting is “°C”.)
(1) (2)
Back
Next
Page
Page 1/ 3 Initial Setting
Date Setting
R.C.Group
Name Setting
Temp. Unit
Setting
R.C. Sensor
Setting
°C
°C
°F
°F
Temp. Unit Setting
Cancel OK
When the [OK] is touched, after a setting change screen is
displayed, the display returns to the “Initial Setting” screen.
3-9-3 R.C.Group Name Setting
(1) Touch the [R.C.Group Name
Setting] on the “Initial Setting”
screen.
“R.C.Group Name Setting”
screen is displayed.
Back
Next
Page
Page 1/ 3 Initial Setting
Date Setting
R.C.Group
Name Setting
Temp. Unit
Setting
R.C. Sensor
Setting
Description of the screen
R.C.Group Name Setting
Cancel OK
Fixed
Phrase
UVW
XY
Z./
_–
ABC
DE
ABCDEFGHIJKLM│ Over
FGH
IJ
KLM
NO
0–9
SP BS
PQR
ST
(a)
(b)
(c)
(d)
(e)
(f)
(a) Input area:
When inputting more than 12 characters, “Over” is
shown at the right end.
(b) Character keys:
Touch the same key until the character to be used is dis-
played.
(c) Fixed Phrase key:
[Floor, Corridor, Offi ce, Conf Room, Receipt Room, Room,
Room No., Front, Side, Entrance, Outlet, East, West,
South, North, Window] is registered. Touch the [Fixed
Phase] key until the sentence to be used is displayed.
(d) Space key
(e) Backspace key
(f) Cursor keys
Change the R.C. Group Name
(2) Touch each key and enter the name. When the [OK] is
touched, after a setting change screen is displayed, the
display returns to the “Initial Setting” screen.
3-9-4 R.C. Sensor Setting
(1) Set the [R.C. Sensor Setting] on the “Initial Setting”
screen.
(2) “R.C. Sensor Setting” screen is displayed. Touch the
[Used].
(1) (2)
Back
Next
Page
Page 1/ 3 Initial Setting
Date Setting
R.C.Group
Name Setting
Temp. Unit
Setting
R.C. Sensor
Setting
R.C. Sensor Setting
Cancel OK
Used
Not Used
When the [OK] is touched, after the data is transmitted
to the indoor unit, the display returns to the “Initial Set-
ting” screen.
3-9-5 Password Setting
(1) Touch the [Password Setting]
on the “Initial Setting” screen.
Back
Previous
Page
Page 2/ 3 Initial Setting
Password Setting
Display Item
Setting
Master Indoor
Unit Setting
Next
Page
RC Master/
Slave Setting
Change the Password
(2) “Password Setting” screen is displayed. Touch the
[Change Password].
(3) “Password Verifi cation” screen is displayed. Enter the
current password, and touch the [OK].
(2) (3)
Password Setting
Change Password
Change Setting
Back
0
CL
5
1
6
2
7
3
8
4
9
Cancel OK
Password Verification
Enter Current Password
NOTE
The default password is “0000” (4 digits).
(4) If the password is entered cor-
rectly, the “Change Password”
screen is displayed.
0
CL
5
1
6
2
7
3
8
4
9
Cancel OK
Change Password
Enter New Password
When the new password is entered and the [OK] is
touched, after the setting change screen is displayed,
the display returns to the “Password Setting” screen.
En-20
9373329831-02OMEnUTY-RNRT.indd209373329831-02OMEnUTY-RNRT.indd20 2021/11/1913:23:042021/11/1913:23:04