Fujitsu UTY-RNRT - CONTROL; On and Off; Operation Settings; Zone Select

2 CONTROL
2-1 On and Off
(1) Press the [On/Off ] button.
26.0
26.0
°C
°C
Cool
Set Temp.
Mode Fan
Fri 10:00AM
Auto
Zone MenuStatus
On/Off button
Power indicator
lamp
The Power indicator lamp remains lit while the indoor
unit is operating.
NOTE
The On/OFF button cannot be operated at screens other
than the monitor mode screen.
2-2 Operation Settings
2-2-1 Set the Operation Mode
(1) Touch the [Mode] on the monitor mode screen.
(2) “Mode” screen is displayed. Select the operation mode.
(1) (2)
Zone
26.0
26.0
°C
°C
Cool
Auto
Set Temp.
Mode
MenuStatus
Fan
Fri 10:00AM
Mode
Cancel
Cool Dry Heat
Fan
OK
Auto
Depending on the model of
the indoor unit, [Custom Auto]
is displayed instead of [Auto].
26.26.0
°C
Custom
Auto
Set Te
Mode
Dry Heat
Fan
OK
Custom
Auto
NOTES
• Only selectable modes are displayed. The select-
able modes may be diff erent depending on the
system confi guration and operation status. Refer
to [4 OPERATION TIPS]→[4-1 Selectable modes].
• When the “Fan” is selected,
the temperature cannot be
set.
Fan
Auto
Set Temp.
Mode
MenuStatus
Fan
Fri 10:00AM
• [Auto] or [Custom Auto] mode can be used in the
R.C. Group to which Master Indoor Unit is set. It is
not displayed at other R.C. Group.
• When the operation mode is switched in a heat
recovery system, operation preparations may take
some time, but this is not a malfunction.
(3) When the [OK] is touched, the display returns to the
monitor mode screen.
2-2-2 Set the Temperature
(1) Touch the [Set Temp.] on the monitor mode screen.
(2) “Set Temp.” screen is displayed. Adjust the room tem-
perature with the [
] or [ ].
(1) (2)
Zone
26.0
26.0
°C
°C
Cool
Auto
Set Temp.
Mode
MenuStatus
Fan
Fri 10:00AM
26.0
26.0
°C
°C
Set Temp.
Cancel OK
When the operation mode is
set to [Custom Auto], set the
cooling and heating tempera-
ture.
20.0 28.0
°C°C
Set Temp.
Cancel OK
HeatCool
NOTES
• The settable temperature range is diff erent depend-
ing on the operation mode. Refer to [4 OPERA-
TION TIPS]→[4-3 Selectable Temperature Range].
• When the “Set Temp. Range Setting” is set, the se-
lectable temperature conforms to the setting. Refer
to [3 SETTING] → [3-6 Special Setting] → [3-6-3
Set Temp. Range Setting].
(3) When the [OK] is touched, the display returns to the
monitor mode screen.
2-2-3 Set the Fan Speed
(1) Touch the [Fan] on the monitor mode screen.
(2) “Fan” screen is displayed. Select the fan speed with the
[
] or [ ].
(1) (2)
Zone
26.0
26.0
°C
°C
Cool
Auto
Set Temp.
Mode
MenuStatus
Fan
Fri 10:00AM
Fan
Cancel OK
Auto
(3) When the [OK] is touched, the display returns to the
monitor mode screen.
2-3 Zone Operation
2-3-1 Zone Select
Touch the [Zone] on the monitor
mode screen.
Zone
26.0
26.0
°C
°C
Cool
Auto
Set Temp.
Mode
MenuStatus
Fan
Fri 10:00AM
The “Zone Select” screen is dis-
played.
[ ]
Zone Select
Zone
Operation
Sensor
Method
Priority
Sensor
Zone Group Operation
Group3
Back
NOTES
• If not connected to the zone interface, this item is not
displayed on the monitor mode screen.
• This item is controllable only when the air conditioner is
operating.
En-7
9373329831-02OMEnUTY-RNRT.indd79373329831-02OMEnUTY-RNRT.indd7 2021/11/1913:23:022021/11/1913:23:02