Fukuda Denshi DynaScope 7000 Series User Manual (English)

Other manuals for Fukuda Denshi DynaScope 7000 Series

Questions and Answers:

F
fsmithAug 22, 2025
How to turn on Fukuda Denshi DynaScope 7000 Medical Equipment DS-7000 when the power supply LED does not light?
- T
  Teresa FernandezAug 22, 2025
  First, ensure the power supply switch on the front of the DS-7000 is turned ON. If the power still doesn't turn on, the fuse inside the AC inlet may have blown. Determine the cause of the blown fuse before replacing it. If a quiet electronic sound is present, the fail-safe device on the CPU board may be functioning, or a data error has occurred.
J
Jessica NixonSep 2, 2025
What does 'TEMP not connected' mean on Fukuda Denshi DynaScope 7000 and how to fix it?
- N
  nicholaspetersonSep 2, 2025
  This message appears when the temperature sensor is disconnected during temperature monitoring. To resolve this, plug in the temperature sensor. This will clear the message and silence the alarm.
S
Steven HuberSep 1, 2025
Why does Fukuda Denshi DynaScope 7000 reset display configuration every time I turn it on?
- C
  Christine WilsonSep 1, 2025
  The long-term backup battery on the CPU board is likely depleted. Replace the long-term backup battery. After replacement, set the rotary switch inside the maintenance cover to the initial setting (F), and turn the power ON again. After the program starts, turn the rotary switch back to '0'. If the problem persists, consider a faulty CPU board.
R
Rachael MedinaAug 31, 2025
Why does recall data disappear when I turn off my Fukuda Denshi Medical Equipment?
- P
  Patricia RobinsonAug 31, 2025
  Ensure the power has been turned ON for more than 1 hour, as 5 minutes of backup is performed only after this duration. If the issue persists, the short-term backup battery may be depleted and needs replacement. If replacing the battery doesn't resolve the problem, a faulty CPU board might be the cause.
H
hhawkinsAug 30, 2025
Why is the alarm sound low or not working on my Fukuda Denshi DynaScope 7000 Medical Equipment?
- A
  Ashley WhiteAug 30, 2025
  Check the alarm settings to ensure Alarm Silence, Alarm Off, or Night Mode is not enabled. Also, verify that the alarm volume is set appropriately in the tone setup menu.
C
Carolyn PerryAug 28, 2025
How to fix unresponsive touch panel keys on Fukuda Denshi Medical Equipment?
- P
  phillipjohnsonAug 28, 2025
  The keys may have shifted over time, requiring calibration.
G
Gary MillerAug 27, 2025
What to do if Fukuda Denshi DynaScope 7000 keeps restarting?
- R
  robert10Aug 27, 2025
  The memory data may have been corrupted due to noise. Set the rotary switch inside the maintenance cover to the initial setting (F), then turn the power ON again. After the program starts, return the rotary switch to '0'. If the issue continues, consider a faulty CPU board.
R
Ryan RodriguezAug 26, 2025
How to fix a blurry display on Fukuda Denshi DynaScope 7000 Medical Equipment?
- V
  Valerie SmithAug 27, 2025
  Adjust the display brightness to an appropriate level. Also, check if the monitor is set to night mode and cancel it if necessary.
D
Derek CampbellAug 25, 2025
Why is the cuff not inflating on my Fukuda Denshi DynaScope 7000, even though the pump is running?
- M
  Michael WilliamsAug 26, 2025
  The air hose may not be firmly connected, causing air leakage. Check if the air hose is properly connected. Also, the cuff size may not match the selected patient type; verify that the cuff size is appropriate for the patient.
J
joshua33Aug 25, 2025
What to do if the 'Check Electrodes' message is displayed on Fukuda Denshi DynaScope 7000?
- L
  Leah MccallAug 25, 2025
  If you see a 'Check Electrodes' message, it means an electrode is detached or not making good electrical contact with the skin. Ensure all electrodes are properly attached.

Fukuda Denshi DynaScope 7000 Series Specifications

General

Category	Medical Equipment
Type	Patient Monitor
Display	Color LCD
Paper Speed	25/50 mm/s
Input Impedance	≥10 MΩ
Power Supply	AC power, Rechargeable battery
ECG	Yes
Respiration	Yes
SpO2	Yes
NIBP	Yes
Temperature	Yes
Storage	Internal memory
Operating Humidity	30% to 85% (non-condensing)
Weight	Approx. 5 kg (including battery)