Technical Support is available 8am-5pm PST. Monday - Friday
support@fslaser.com • 702-802-3103
80
Technical Support is available from 8am to 5pm (PST) M - F at support@fslaser.com.
Stopping the Laser
Once a project has begun, the laser will continue until the project is complete. If for any reason
an operator needs to stop the laser immediately, choose one of these options:
1. Open the Lid. The large workbed access lid is installed with a device that automatically (and
instantly) cuts off the laser if it is opened even slightly. This should be your first method of stopping
the laser during an emergency. This is a safety feature of Muse 3D and under no circumstances
should this safe lid auto-shutoff device be tampered with or removed. Doing so will void your
machine’s warranty. If the machine ever fails to shut off the laser when the safety lid is open,
immediately unplug the ma- chine and contact customer service.
2. Touch Screen Pause Button. Top of Machine Pause Button. On the top of Muse 3D machines
there is a button that can pause or stop the laser. Press once to pause the job. Press and hold to
stop the job. Once a job is stopped, starting again will start the project from the beginning.
3. E-Stop. On the touch screen, in the lower right corner, is an “Emergency” stop button (E-Stop).
Pushing this button will instantly cut power to the laser. Be aware this is still part of the touch screen
and is fragile. Do not slam this button.
4. Software Pause Button. In the software, on your computer, you can click the Pause Button (con-
verted Play button when laser is running a job) to halt the laser. This may take a second to process,
so it is not recommended as a method of stopping the laser in an emergency.
5. Power Switch. At the back of the machine is the power on/off switch. Flipping this switch to the off
position instantly cuts power from the laser head (and the entire machine). Using this option will
completely cut power from the laser, the touch screen and all other Muse 3D systems.
6. Unplug Power. You can also simply unplug the power cord of the main Muse 3D unit. This should
be a last resort method for emergencies as the other methods are quicker to access and prevent
pulling on cords and connections.
Section VII. Operations
Stopping the laser
Once a project has begun, the laser will continue until the project is complete. If for any reason an operator
needs to stop the laser immediately, choose one of these options:
1.Open the Lid. The large workbed access lid is installed with a device that automatically (and instantly)
cuts off the laser if it is opened even slightly. This should be your rst method of stopping the laser during an
emergency. This is a safety feature of Muse 3D and under no circumstances should this safe lid auto-shutoff
device be tampered with or removed. Doing so will void your machine’s warranty. If the machine ever fails to
shut off the laser when the safety lid is open, immediately unplug the machine and contact customer service.
2. Touch Screen Pause Button. Top of Machine Pause Button. On the top of Muse 3D machines there is a
button that can pause or stop the laser. Press once to pause the job. Press and hold to stop the job. Once a
job is stopped, starting again will start the project from the beginning.
3. E-Stop. On the touch screen, in the lower right corner, is an “Emergency” stop button (E-Stop). Pushing this
button will instantly cut power to the laser. Be aware this is still part of the touch screen and is fragile. Do not
slam this button.
4. Software Pause Button. In the software, on your computer, you can click the Pause Button (converted
Play button when laser is running a job) to halt the laser. This may take a second to process,so it is not
recommended as a method of stopping the laser in an emergency.
5. Power Switch. At the back of the machine is the power on/off switch. Flipping this switch to the off position
instantly cuts power from the laser head (and the entire machine). Using this option will completely cut power
from the laser, the touch screen and all other Muse 3D systems.
6.Unplug Power. You can also simply unplug the power cord of the main Muse 3D unit. This should be a last
resort method for emergencies as the other methods are quicker to access and prevent pulling on cords and
connections.
To Next Page
Loading...