What does 'BATTERY ALM!(PRCSSR)' mean on Furuno Compass?
The 'BATTERY ALM!(PRCSSR)' message on your Furuno Compass indicates that the voltage of the battery in the processor unit is low. Have the battery replaced at your earliest convenience.
What does 'BACKUP ERROR!(DISP)' mean on Furuno SC-60 Compass?
The 'BACKUP ERROR!(DISP)' message on your Furuno Compass indicates that corrupted backup data was found in the display unit at power on. Default settings are automatically restored.
What does 'BACKUP ERROR!(PRCSSR)' mean on Furuno Compass?
The 'BACKUP ERROR!(PRCSSR)' message on your Furuno Compass indicates that corrupted backup data was found at the processor unit at power on. Default settings are automatically restored.
What does 'DGPS ERROR!' mean on Furuno SC-60 Compass?
The 'DGPS ERROR!' message on your Furuno Compass means that DGPS data from the DGPS receiver in the processor unit is lost for one minute. The ship may not be within the DGPS service area.
What does 'DATA ERR!' mean on Furuno SC-60?
The 'DATA ERR!' message on your Furuno Compass indicates that GPS data from the GPS receiver in the processor unit is lost for one minute. Heading output is stopped and the heading indication shows '- - -'. Check the navigator.
General| Type | Satellite Compass |
|---|---|
| Resolution - Heading | 0.1° |
| Resolution - Roll/Pitch | 0.1° |
| Update Rate | 10 Hz |
| Display | LCD |
| Temperature Range | -15°C to +55°C |
| Accuracy - Heading | 0.5° |
| Heading Accuracy | 0.5° |
| Interfaces | NMEA 0183 |
| Operating Temperature | -15 to +55 °C |
Describes warnings and cautions for safe operation of the equipment.
Provides warnings and notices for safe equipment installation.
Highlights the key capabilities and advantages of the SC-60 compass.
Lists core technical specifications of the satellite compass.
Details specifications related to the display unit.
Covers data output and input specifications for external connections.
Specifies power requirements and consumption.
Outlines operating temperature, humidity, and EMC standards.
Describes the color specifications for the unit's components.
Discusses factors for choosing optimal mounting locations for antennas.
Provides guidance for installing display and processor units.
Details the process for installing the SC-series antenna units.
Explains mounting considerations specific to the DGPS antenna.
Guides on how to mount the processor unit in various locations.
Details the procedure for bulkhead mounting the processor unit.
Describes mounting the processor unit under a desk.
Explains how to correct orientation issues of the processor unit.
Guides on mounting the display unit in desktop or overhead configurations.
Details the flush mounting procedure for the display unit.
Covers general wiring procedures for connecting system components.
Guides on performing initial setup procedures for the system.
Explains how to select the primary source for heading data.
Describes how to configure heading data output formats via jumpers.
Details connections for various external navigation devices.
Guides on installing the optional DGPS beacon receiver.
Describes the function of each button on the display unit.
Explains how to power the unit on and off.
Details how to adjust display brightness and contrast.
Guides on selecting different display modes for information.
Describes various display screens like Steering, Compass, ROT.
Explains how to configure and manage system alarms.
Describes how to check the status of satellite reception.
Covers settings for smoothing position, speed, and course.
Explains how heading data is output in IEC 61162-1 format.
Details the navigation data output configuration.
Describes interface settings for data communication protocols.
Configures log pulse output for speed data.
Sets the talker ID for heading data output.
Explains how to match GPS datum with chart systems for accuracy.
Configures display units for distance and speed.
Sets the time difference for local time display.
Selects between 12-hour and 24-hour time display.
Guides on using the simulated operation mode.
Details manual configuration of DGPS settings.
Explains how to add user-defined DGPS beacon stations.
Describes how to modify existing user beacon station entries.
Guides on deleting specific DGPS beacon stations.
Explains how to remove all programmed beacon stations.
Covers settings for last-used heading and rate-of-turn smoothing.
Manages speed display, distance source, and tide drift smoothing.
Details how to reset the distance run counter.
Provides guidelines for regular maintenance to ensure performance.
Offers procedures to resolve common operational issues.
Explains how to run diagnostic tests for equipment checks.
Shows how to display the software program numbers.
Details procedures for clearing GPS and system data.
Guides on replacing internal batteries for data storage.
Explains the procedure for replacing the power board fuse.
Lists and explains common error messages and their remedies.
Lists geodetic chart codes used for datum matching.
Describes the digital interface standards and data transmission.
Provides circuit diagrams for various ports.
Explains the format of various NMEA and proprietary data sentences.
Details the functions and specifications of the unit's ports.
Shows the physical location of major components within the processor unit.
Lists the main replaceable components of the equipment.
Discusses factors for choosing mounting locations for the SC-603 antenna.
Details the procedure for installing the SC-603 antenna unit.
Explains how to weld the antenna unit to the mast.
Lists packing contents for the SC-303 antenna unit.
To Next Page
