What to do if there is no sound from my Fusion Amplifier?
If you're not getting any sound from your Fusion Amplifier, there are a few things to check: * Make sure the RCA connection to the head unit is secure. * Verify that you've properly set up the amplifier gain level control. * Check the head unit volume level. * Inspect all power, remote-on, and ground connections. * Ensure the speaker connections are correctly wired.
What to do if my Fusion Amplifier is not switching on and the power LED is off?
If your Fusion Amplifier isn't turning on and the power LED is off, there could be several reasons. First, check the fuses and connections to the battery to ensure there's +12V reaching the power wire. Next, verify the remote-on connections to the head unit to make sure the remote wire has power. Also, inspect the amplifier's fuse and replace it with the correct type and amperage if it's blown.
Why is my Fusion Amplifier not working, even though the Power LED is on?
If your Fusion Amplifier's power LED is on but there's no output, it might be overheating. Try moving the amplifier to a more ventilated area. Also, check the speaker wires to ensure none are shorted to each other.
General| Peak Power | 1600W |
|---|---|
| Input Sensitivity | 200mV - 6V |
| THD | <0.05% |
| Amplifier Class | Class D |
| Frequency Response | 20Hz - 20kHz |
| Operating Voltage | 10.5 V to 16 V |
| Bass Boost | 0 dB to +12 dB |
| RMS Power (2 Ohms) - Mono | 800W |
| Dimensions | 12-1/4 x 2-1/8 x 7-1/8 [310mm x 54mm x 180mm] |
Specifies the peak output power in Watts for the amplifier.
Defines the range of audio frequencies the amplifier can reproduce.
Provides the physical dimensions of the amplifier in millimeters.
Details the RMS power output at different impedance loads and distortion levels.
Essential steps before and during installation to ensure safety and proper function.
Guidance on selecting a suitable mounting location and ensuring adequate ventilation.
Advice on avoiding mounting the amplifier near critical vessel equipment or antennas.
Connect directly to the +12V battery terminal using a 4 gauge cable with an inline fuse.
Connect directly to the vessel's earth system via a 4 gauge cable.
Connect to the Head Unit's remote turn-on wire or a switched 12V source.
Important precautions for wiring, protecting cables, and ensuring terminal isolation.
Instructions on connecting RCA cables from the source unit, avoiding power cables.
Procedure to match amplifier input level to the head unit output for optimal volume without distortion.
Table detailing crossover types, frequencies, and bass boost options for different zones and subwoofers.
Troubleshooting steps for when the power LED is not illuminated.
Solutions for when the amplifier is on but not producing sound or is overheating.
Common causes and solutions for lack of audio output from the amplifier.
Detailed diagrams showing the physical dimensions of the amplifier in millimeters and inches.
Description of terminals for connecting speakers to the amplifier.
Connection point for zone 1 low-level audio input from the head unit.
Connection point for zone 2 low-level audio input from the head unit.
Connection point for subwoofer low-level audio input from the head unit.
Connects an optional remote controller for subwoofer volume adjustment.
Displays operational status and fault indication for the amplifier.
Details the required fuse type and rating for the amplifier.
Specific instructions for +12V, Remote Turn-On, and Ground connections.
Settings for crossover frequencies, filter types, and input level matching for all zones.
Controls for subwoofer low-pass filter, audio source, and low-frequency shaping.
Diagram illustrating the wiring for a 3-channel speaker setup.
Diagram illustrating the wiring for a 5-channel speaker setup.
List of essential tools required for amplifier installation.
Visual representation of Ohm's Law formulas for electrical calculations.
Instructions and diagram for wiring dual voice coil subwoofers in parallel for 2 Ohm operation.
Instructions and diagram for wiring dual voice coil subwoofers in series for 8 Ohm operation.
Formula and example for calculating load impedance when wiring two speakers in parallel.
Formula for calculating load impedance when wiring two speakers in series.
Section to record serial number, date of purchase, and affix receipt.
Instructions for registering the product online for warranty purposes.
Statement regarding the 3 Year Limited Consumer Warranty.
Links and information for further product details and installation support.
Guidance on responsible disposal of electrical equipment.
Warning about high sound levels and the risk of permanent hearing loss.
Contact phone numbers for Fusion support in various regions.
Mentions of certifications, trademarks, and copyright information.
Product model number, revision, date, and country of manufacture.
To Next Page