151
<Model Menu (Airplane/Glider Functions)>
ŏ6HOHFWWKHIXQFWLRQQDPH
and return to the Model
menu by pushing the RTN
button or pushing the
HOME/EXIT button.
<Push Dial>
RETURN
ELEVATOR
ELEVATOR2
V-TAIL
ELEVATOR
ELEVATOR2
AILVATOR
FLP2
(CamberFlap)
FLP1
(CamberFlap)
CMBFLP to ELE
>&RUUHVSRQGLQJPRGHOW\SH@$LUSODQHJOLGHU
DLOHURQVÁDSRUPRUH
When the camber/speed flaps are utilized,
the aircraft might experience, a change in pitch.
This mix compensates for such changes by
incorporating elevator input.
ŏ7KHHOHYDWRUVHUYRVXSGRZQUDWHVFDQEH
DGMXVWHGVHSDUDWHO\,IWKHPL[LQJGLUHFWLRQLV
UHYHUVHGFKDQJHWKHPL[LQJUDWHSRODULW\RU²
ŏ0L[LQJGXULQJIOLJKWFDQEHWXUQHG212))E\
VHWWLQJDVZLWFK$OZD\V21DW>@VHWWLQJ
ŏ(OHYDWRUUDWH
DGMXVWPHQW
Setting method
Ɣ$FWLYDWHWKHIXQFWLRQ
0RYHWKHFXUVRUWRWKH>$&7@LWHPDQGSXVK
the RTN button to switch to the data input
PRGH6HOHFWWKH$&7PRGHE\VFUROOLQJWKH
3XVKGLDO
*The display blinks.
3XVKWKH571EXWWRQWRDFWLYDWHWKHIXQFWLRQ
DQGUHWXUQWRWKHFXUVRUPRGH21LV
GLVSOD\HG
When setting a switch, move the cursor to
WKH>6:@LWHPDQGSXVKWKH571EXWWRQWRFDOO
WKHVHOHFWLRQVFUHHQ6HOHFW WKHVZLWFKDQG
VHWLWV21GLUHFWLRQ$OZD\V21DWVHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ0L[LQJUDWHDGMXVWPHQW
0RYHWKHFXUVRUWRWKH5$7(RU5$7(LWHP
and push the RTN button to switch to the
GDWDLQSXWPRGH$GMXVWWKHPL[LQJUDWH
LQGHSHQGHQWO\E\VFUROOLQJWKH3XVKGLDO
,QLWLDOYDOXH
$GMXVWPHQWUDQJHa
*When the RTN button is pushed for one second, the rate is
reset to the initial value.)
3XVKWKH571EXWWRQWRHQGWKHDGMXVWPHQW
and return to the cursor mode.
ŏ6HOHFW>&0%)/3WR(/(@DWWKH0RGHOPHQXDQG
access the setup screen shown below by pushing
the RTN button.
*The display screen is an
example. The actual screen
depends on the model type.
6FUROOLQJ
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
ŏ$GMXVWLQJYDOXH
ŏ7RQH[WSDJH
(Glider: Currently selected condition name)