FUTABA 12K - Setting Method

165
<Model Menu (Airplane/Glider Functions)>
Setting method
Ɣ$FWLYDWHWKHPRWRUVSHHGIXQFWLRQ
When using motor speed function, move the
FXUVRUWRWKH>,1+@ LWHPDQGSXVKWKH571
button to switch to the data input mode.
6HOHFWWKH>$&7@E\VFUROOLQJWKH3XVKGLDO
and push the RTN button.
Ɣ6LIWLQJWKHERXQGDU\EHWZHHQWKHUDQJHV
 0RYHWKHFXUVRUWRWKH>63(('!@LWHPDQG
push the RTN button to switch to the data
input mode.
 $GMXVWWKHERXQGDU\SRVLWLRQE\VFUROOLQJWKH
3XVKGLDO
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
*When the RTN button is pushed for one second, the rate is
reset to the initial value.)
 3XVKWKH571EXWWRQWRUHWXUQWRWKHFXUVRU
mode.
Ɣ2SHUDWLRQVSHHGDGMXVWPHQW
 0RYHWKHFXUVRUWRWKH>,1@RQWRRIIRU>287@
RIIWRRQLWHPDQGSXVKWKH571EXWWRQWR
switch to the data input mode.
 $GMXVWWKHRSHUDWLRQVSHHG\RXZDQWWRVHW
E\VFUROOLQJWKH3XVKGLDO
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
*When the RTN button is pushed for one second, the rate is
reset to the initial value.)
 3XVKWKH571EXWWRQWRUHWXUQWRWKHFXUVRU
mode.
Ɣ6HW5HVHWWKHRQHWLPHRSHUDWLRQ
 0RYHWKHFXUVRUWRWKH>21(7,0(@LWHPDQG
push the RTN button to switch to the data
input mode.
 6HOHFWWKH>$&7@E\ VFUROOLQJWKH3XVKGLDO
and push the RTN button to set the one time
operation.
* When you want to reset one time operation, set the ACT/
INH item to [INH] and then reset it to [ON].
ŏ0RWRUIXQFWLRQVZLWFK
current position
Ɣ6WDUWVZLWFKIXQFWLRQ
:KHQDFWLYHWKH67$576:DOORZVWKH
PRWRUVVWDWHWRFKDQJHIURP2))WR217KH
PRWRULV21ZKHQWKHPDLQ6:DQG67$57
6:DUHWXUQHG21VLPXOWDQHRXVO\7KHPRWRU
FKDQJHVWR2))RQO\ZKHQWKHPDLQ6:LV
WXUQHGRII,I67$576:LVWXUQHG2))EXWWKH
PDLQ6:LVVWLOO21WKHPRWRUUHPDLQV21
[START SW function example]
When the throttle (motor) stick is assigned as the "START SW",
and the low throttle position of the throttle curve is adjusted, the
motor starts operating with the initial stick movement. The motor
will not cease functionality even if the stick position is returned to
it's lowest setting.
Ɣ7ULPHIIHFWLQYDOLGVHWWLQJLQPRWRU2))
,IRQHRIWKHWULPOHYHUVLVDVVLJQHGWRWKH
Motor function, it is possible to turn the
motor off with the trim lever. To maintain
FRPSDWLELOLW\DIWHUXSGDWLQJWKH7.6WKH
WULPVHWWLQJLVDGMXVWHGWRWKHRQSRVLWLRQ
+RZHYHULWLVVXJJHVWHGWRUHWXUQLWWRWKHRII
position accordingly in the programming of
the transmitter.
*Data Reset will return the trim setting to the off position.
Ɣ6FUHHQDWWKHWLPHRIWKHPRWRU2))VHWWLQJ
:KHQWKH027252))VHWWLQJLVKLJKOLJKWHG
you will note the presence of the small cursor
WKDWLQGLFDWHVWKH027252))SRVLWLRQ7R
DGMXVWWKLV027252))SRVLWLRQXVHWKH
throttle stick to move the cursor accordingly.
When satisfied with this position, push and
hold the RTN button on the transmitter.
*The larger cursor is used to indicate the output of the motor
FKDQQHO7KLVFXUVRUUHÀHFWV DQ\WKURWWOHFXUYHVDQGPRWRU
mixing which may be active.
Ɣ7KURWWOHFXUYHEXWWRQ
:KHQ&859(EXWWRQLVFKRVHQDWKURWWOH
curve screen opens.
*When a throttle function is assigned to either channel, the
"CURVE" button is not displayed because a throttle curve
does not function as a motor curve.
ŏ212))GLUHFWLRQ