FUTABA 12K - Page 164

164
<Model Menu (Airplane/Glider Functions)>
ŏ6HOHFWWKHIXQFWLRQQDPH
and return to the Model
menu by pushing the RTN
button or pushing the
HOME/EXIT button.
<Push Dial>
RETURN
MOTOR
>&RUUHVSRQGLQJPRGHOW\SH@$LUSODQHJOLGHUJHQHUDO
This function lets you set the speed when the
motor of an F5B or other EP glider is started via
a switch. The operation speed can be set for two
ranges, slow speed flight and high speed flight
(Speed 1/Speed 2). This function can also be
operated as a safety function by programming it to
a switch.
ŏ7KH,QVLGHDQG2XWVLGHRSHUDWLQJVSHHGVFDQ
EHDGMXVWHGLQGHSHQGHQWO\LQUDQJHV6SHHG 
6SHHG
ŏ7KHERXQGDU\EHWZHHQWKH  UDQJHVFDQEHVHW
)URP6SHHGWR6SHHG
ŏ7KHRSHUDWLRQDOVSHHGFDQRQO\EHDFWLYDWHGDW
WKHLQLWLDORSHUDWLRQ+RZHYHURSHUDWLRQ FDQEH
UHSHDWHGE\VHWWLQJWKHVZLWFKWR2))EHIRUHWKH
RSHUDWLRQLVÀQLVKHG:KHQ\RXZDQWWRUHVHWRQH
WLPHRSHUDWLRQVHWWKH$&7,1+LWHPWR>,1+@DQG
WKHQUHVHWLWWR>21@
ŏ7KHPRWRUFKDQQHOLVFRQWUROOHG E\6:**OLGHU
,QLWLDOVHWWLQJ:KHQFKDQJLQJWKHVZLWFKRU VWLFN
ZKLFKFRQWUROVWKHPRWRUÀUVWFKDQJH)XQFWLRQRI
the Linkage menu.
ŏ,IWKH0RGHO7\SHVHOHFWHGLV$LUSODQHWKH02725
IXQFWLRQLVFKDQJHGIURP,1+WR21 DQG LWLVQRW
assigned to another channel, the changes from
the throttle channel to the motor channel are
enabled.
Note: Initial setting does not assign a motor
channel according to the model type. Prior to
DVVLJQLQJWKHPRWRUFKDQQHOÀQGDQXQXVHG
channel. Then, use the Function menu of the
Linkage menu.
Set [Control] to the switch you want to use
and [Trim] to [--].
Note: When using this function, always check
the initial operation with the propeller
removed.
ŏ6HOHFW>02725@DWWKH0RGHOPHQX
and access the setup screen shown
below by pushing the RTN button.
6FUROOLQJ
ŏ0RYLQJFXUVRU
ŏ6HOHFWLQJPRGH
ŏ$GMXVWLQJYDOXH
ŏ7RQH[WSDJH
Setting method
Ɣ$FWLYDWHWKHIXQFWLRQ
When using this function, move the cursor to
WKH>$&7,1+@LWHPDQGSXVKWKH571EXWWRQ
WRVZLWFKWRWKHGDWDLQSXWPRGH6HOHFWWKH
>$&7@E\VFUROOLQJWKH3XVKGLDODQGSXVKWKH
RTN button.
 :KHQVHOHFWLQJWKH212))VZLWFKPRYHWKH
cursor to the switch item and push the RTN
EXWWRQWRDFFHVVWKHVHOHFWLRQVFUHHQ6HOHFW
WKHVZLWFKDQGVHWLWV21GLUHFWLRQ$OZD\V
21DWVHWWLQJ
*For a description of the switch selection method, see the
description at the back of this manual.
Ɣ0RWRURIISRVLWLRQVHWWLQJ
 0RYHWKHFXUVRUWRWKH>027252))@LWHP
and push the RTN button for one second
ZKHQWKHPRWRUIXQFWLRQVZLWFK6*HWFLV
LQWKHPRWRU2))SRVLWLRQ\RXZDQWWRVHW7KH
direction of the motor switch is memorized.
7KHVFUHHQJUDSKGLVSOD\2))GLUHFWLRQDOVR
changes.
Note:
ŏ)LUVWGHFLGHWKHPRWRU2))GLUHFWLRQDQGWKHQ
set the speed. When you want to reset the
motor OFF direction, also reset the speed.
ŏ:HUHFRPPHQGWKDW0RWRU2))EHVHWLQ
combination with F/S.
ŏ6HWWKHEDVLFRSHUDWLRQGLUHFWLRQZLWKWKH
Reverse function to match the ESC used.
ŏ$OZD\VVHWWKH0RWRU2))SRVLWLRQ