FUTABA 8FG - Page 33

33
5HFHLYHUDQG6HUYR,QVWDOODWLRQ!
3UHFDXWLRQVZKHQPRXQWLQJWKHUHFHLYHUDQGVHUYRV
)ROORZWKHVHJXLGHOLQHVWRSURSHUO\PRXQWWKHVHUYRVUHFHLYHUDQGEDWWHU\
0DNHFHUWDLQWKH
DOLJQPHQWWDERQWKHEDWWHU\
VZLWFKDQGVHUYRFRQQHFWRUVLVRULHQWHGFRUUHFWO\
and “keys” into the corresponding notch in the
receiver or connectors before plugging them
LQ:KHQXQSOXJJLQJFRQQHFWRUVQHYHUSXOORQ
WKHZLUHV$OZD\VSXOORQWKHSODVWLFFRQQHFWRU
instead.
,I\RXUDLOHURQVHUYRRURWKHUVDUHWRRIDUDZD\
WRSOXJLQWRWKHUHFHLYHUXVHDVHUYRH[WHQVLRQ
cord to extend the length of the servo lead.
Additional Futaba extension cords of varying
lengths are available from your hobby dealer.
$OZD\VXVHDQH[WHQVLRQRIWKHSURSHUOHQJWK
Avoid plugging multiple extensions together to
attain your desired length. If distance is greater
WKDQ´RUPXOWLSOHRUKLJKFXUUHQWGUDZVHUYRV
DUHEHLQJXVHGXVH)XWDED+HDY\'XW\VHUYR
extensions.
$OZD\VPRXQWWKHVHUYRVZLWKWKHVXSSOLHG
UXEEHUJURPPHWV. Do not over tighten the
VFUHZV1RSDUWRIWKHVHUYRFDVLQJVKRXOGFRQWDFW
WKHPRXQWLQJUDLOVVHUYRWUD\RUDQ\RWKHUSDUW
RIWKHDLUSODQHKHOLFRSWHUVWUXFWXUH2WKHUZLVH
YLEUDWLRQZLOOEHWUDQVPLWWHGWRWKHVHUYRFDXVLQJ
SUHPDWXUHZHDUDQGRUVHUYRIDLOXUH
Servo
Rubber
grommet
Servo
Rubber
grommet
1RWHWKHVPDOOQXPEHUVPROGHGLQWR
each arm on the Futaba 4-arm servo arms. The
QXPEHUVLQGLFDWHKRZPDQ\GHJUHHVHDFKDUP
LV³RII´IURPGHJUHHVWRFRUUHFWIRUPLQXWH
manufacturing deviations from servo to servo.
7RFHQWHUWKHVHUYRVFRQQHFWWKHPWRWKHUHFHLYHU
and turn on the transmitter and receiver. Center
WKHWULPVRQWKHWUDQVPLWWHUWKHQ¿QGWKHDUPWKDW
ZLOOEHSHUSHQGLFXODUWRWKHSXVKURGZKHQSODFHG
on the servo.
$IWHUWKHVHUYRVDUHLQVWDOOHGRSHUDWHHDFKVHUYR
over its full travel and check that the pushrods and
servo arms do not bind or contact each other. Also
PDNHVXUHWKHFRQWUROVGRQRWUHTXLUHH[FHVVIRUFH
WRRSHUDWH,IWKHUHLVDQREMHFWLRQDEOHEX]]LQJ
VRXQGFRPLQJIURPDVHUYRWKHUHLVSUREDEO\WRR
much resistance in the control. Find and correct
WKHSUREOHP(YHQLIWKHUHLVQRVHUYRGDPDJH
H[FHVVEDWWHU\GUDLQZLOOUHVXOW
• Use the PRXQWLQJSODWH from the receiver
RQRIIVZLWFKDVDWHPSODWHIRUWKHFXWRXWDQG
VFUHZKROHV0RXQWWKHVZLWFKRQWKHVLGHRIWKH
IXVHODJHRSSRVLWHWKHHQJLQHH[KDXVWDQGZKHUH
LWZRQ¶WEHLQDGYHUWHQWO\WXUQHGRQRURIIGXULQJ
KDQGOLQJRUVWRUDJH%HFHUWDLQWKHVZLWFKPRYHV
ZLWKRXWUHVWULFWLRQDQG³VQDSV´IURP21WR2))
DQGWKDWWKHFXWRXWDOORZVIXOOPRWLRQRIWKH
VZLWFKLQERWKGLUHFWLRQV
:KHQ\RXLQVWDOOWKHVZLWFKKDUQHVVWRWKH
KHOLFRSWHUSOHDVHXVHWKHVZLWFKFRYHU*HQHUDOO\
VDQGZLFKWKHIUDPHEHWZHHQWKHVZLWFKDQGVZLWFK
FRYHUDQGVHFXUHO\WLJKWHQWKHVFUHZV'LIIHUHQW
PRGHOVPLJKWUHTXLUHGLIIHUHQWLQVWDOODWLRQV,IVR
SOHDVHIROORZWKHPRGHOVLQVWUXFWLRQPDQXDO
7RSUHYHQWWKHVHUYROHDGZLUHVIURPEHLQJ
EURNHQE\YLEUDWLRQGXULQJÀLJKWSURYLGHDVOLJKW
DPRXQWRIVODFNRUH[WUDVRWKDWWKHZLUHVWLFNV
out slightly and fasten it at suitable points. In
DGGLWLRQSHULRGLFDOO\FKHFNWKHZLUHGXULQJGDLO\
maintenance.
Fasten about 5-10cm
from the servo outlet
so that the lead wire
is neat.
Slack in the lead wire.