34
5HFHLYHUDQG6HUYR,QVWDOODWLRQ!
5HFHLYHUV$QWHQQD,QVWDOODWLRQ
<RXZLOOQRWHWKDWWKH5+6GLIIHUVLQDSSHDUDQFHIURPWKHVWDQGDUG)XWDEDUHFHLYHU7KLVUHFHLYHU
LQFRUSRUDWHWZRVHSDUDWHDQWHQQDVLQWRWKHLUGHVLJQZKLFKHQDEOHVWKHPWRUHFHLYHWKHUDGLRIUHTXHQF\
WUDQVPLVVLRQDWWZRGLIIHUHQWORFDWLRQV
Antenna
*Must be kept as straight as possible.
Coaxial cable
R6008HS Receiver
)XWDEDVGXDODQWHQQDGLYHUVLW\WKHQVHDPOHVVO\VHOHFWVWKHEHVWVLJQDOUHFHSWLRQEHWZHHQWKHVHDQWHQQDV
to ensure that there is no loss of signal. 
To obtain the best results of the diversity 
IXQFWLRQSOHDVHUHIHUWRWKHIROORZLQJLQVWUXFWLRQV
1. The two antennas must be kept as straight as 
possible. Otherwise it will reduce the effective 
range.
2. The two antennas should be placed at 90 
degrees to each other. 
This is not a critical figure, but the most 
important thing is to keep the antennas 
away from each other as much as possible. 
Larger models can have large metal objects 
that can attenuate the RF signal. In this case 
the antennas should be placed at both 
sides of the model. Then the best RF signal 
FRQGLWLRQLVREWDLQHGDWDQ\Á\LQJDWWLWXGH
3. The antennas must be kept away from 
conductive materials, such as metal, carbon 
and fuel tank by at least a half inch. The 
coaxial part of the antennas does not need 
to follow these guidelines, but do not bend it 
in a tight radius. 
4. Keep the antennas away from the motor, 
ESC, and other noise sources as much as 
possible.
7KHWZRDQWHQQDVVKRXOGEHSODFHGDWGHJUHHVWRHDFKRWKHU
7KHPDLQSXUSRVHRIWKHSKRWRGHPRQVWUDWHVKRZWKHDQWHQQDVKRXOGEHSODFHG
5HFHLYHU9LEUDWLRQDQG:DWHUSURR¿QJ7KHUHFHLYHUFRQWDLQVSUHFLVLRQHOHFWURQLFSDUWV%HVXUH
WRDYRLGYLEUDWLRQVKRFNDQGWHPSHUDWXUHH[WUHPHV)RUSURWHFWLRQZUDSWKHUHFHLYHULQIRDP
UXEEHURURWKHUYLEUDWLRQDEVRUELQJPDWHULDOV,WLVDOVRDJRRGLGHDWRZDWHUSURRIWKHUHFHLYHU
E\SODFLQJLWLQDSODVWLFEDJDQGVHFXULQJWKHRSHQHQGRIWKHEDJZLWKDUXEEHUEDQGEHIRUH
ZUDSSLQJLWZLWKIRDPUXEEHU,I\RXDFFLGHQWDOO\JHWPRLVWXUHRUIXHOLQVLGHWKHUHFHLYHU\RX
PD\H[SHULHQFHLQWHUPLWWHQWRSHUDWLRQRUDFUDVK,ILQGRXEWUHWXUQWKHUHFHLYHUWRRXUVHUYLFH
center for service.
Antenna Antenna