FUTABA 8FG - Page 77

77
0RGHO0HQX&RPPRQ)XQFWLRQV!
Touch the RTN button to end adjustment and
return to the cursor mode.
1HHGOHKLJKWULPZRUNVDVKLJKWULPEDVHGRQWKHFHQWHU
:RUNVOLNH$7/WULP
Ɣ$FFHOHUDWLRQVHWWLQJ$LUSODQH
7KLVIXQFWLRQLVXVHGWRDGMXVWWKHQHHGOHHQJLQHULVH
characteristics during acceleration. This enables an
DFFHOHUDWLRQIXQFWLRQZKLFKWHPSRUDULO\LQFUHDVHVWKHQHHGOH
operation from the throttle stick.
 7KLVIXQFWLRQLVXVHGZKHQWKHUHDUHV\PSWRPVRIWKH
PL[WXUHEHLQJWRROHDQRUWRRULFKZKLFKZRXOGEH
generated by sudden throttle stick inputs.
[Acceleration rate setting (RATE)]
$FFHOHUDWLRQFDQEHDGMXVWHGIRUDWERWKKLJKDQGORZ
settings.
[Damping rate setting (DUMPING)]
7KHUHWXUQWLPHDIWHURSHUDWLRQ'XPSLQJFDQEHVHW
Move the cursor to the rate item you want to
change and touch the RTN button to switch
to the data input mode.
Adjust the rate by scrolling the touch sensor.
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end adjustment and
return to the cursor mode.
[Operation point setting (ACT POS)]
7KHRSHUDWLRQSRLQWDWZKLFKWKHDFFHOHUDWLRQVHWWLQJZLOO
RFFXU,IWKLVSRLQWLVH[FHHGHGDFFHOHUDWLRQLVSHUIRUPHG
Move the cursor to the [ACT POS] item and
hold the throttle stick to the position you
want to change and touch the RTN button
for one second.
Note: When using the acceleration funtion,
since the needle stroke is large, adjust your
settings so there is no binding of your linkage.
Ɣ(QJLQHFXWVHWWLQJ
2SHUDWLRQOLQNHGZLWKWKHWKURWWOHKROGIXQFWLRQWKURWWOHFXW
IXQFWLRQDQGLGOHGRZQIXQFWLRQLVSRVVLEOH7KHWKURWWOHFXW
SRVLWLRQFDQEHDGMXVWHGDFFRUGLQJO\6HWLWWRWKHIXOOFORVHG
position.
Move the cursor to the throttle cut or idle
down item and touch the RTN button to
switch to the data input mode.
Adjust the servo position by scrolling the
touch sensor.
 ,QLWLDOYDOXH7+5&87,'/('2:1
 $GMXVWPHQWUDQJH7+5&87a,'/(
'2:1a
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end the adjustment
and return to the cursor mode.
6HWWLQJPHWKRG
%HIRUHXVLQJWKLVIXQFWLRQDVVLJQWKH>)8(/0,;@IXQFWLRQ
WRDQXQXVHGFKDQQHOLQWKH/LQNDJHPHQX>)81&7,21@
function.
Ɣ$FWLYDWHWKHIXQFWLRQ
1. Move the cursor to the [ACT] item and touch
the RTN button to switch to the data input
mode.
Select the ACT mode by scrolling the touch
sensor.
*The display blinks.
Touch the RTN button to activate the
function and return to the cursor mode. (ON
is displayed.)
2. Move the cursor to the [MIX] item and touch
the RTN button to switch to the data input
mode.
Select the mixing mode you want to change
by scrolling the touch sensor.
*The display blinks.
Touch the RTN button to change the mode
and return to the cursor mode.
:KHQ>0,;@LVVHOHFWHGDWWKH>0,;@LWHPWKHWKURWWOHFXUYH
setting data becomes the mixing master side data. When
>810,;@LVVHOHFWHGWKHWKURWWOHVWLFNSRVLWLRQEHFRPHVWKH
mixing master.
ƔSRLQWFXUYHVHWWLQJ
1. Move the cursor to the point rate setting item
you want to adjust and touch the RTN button
to switch to the data input mode.
Adjust the rate by scrolling the touch sensor.
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHVHUYR
RSHUDWLRQSRVLWLRQLVUHVHWWRWKHLQLWLDOYDOXH
Touch the RTN button to end adjustment and
return to the cursor mode.
2. Repeat this procedure for each point.
Ɣ1HHGOHKLJKWULPVHWWLQJ
1. Move the cursor to the needle high trim
selection item and access the switch setup
screen by touching the RTN button. Select
the needle high trim lever.
)RUDGHWDLOHGGHVFULSWLRQRIWKHVHWWLQJPHWKRGVHH>6ZLWFK
6HWWLQJ0HWKRG@DWWKHEDFNRIWKLVPDQXDO
2. Move the cursor to the TRIM rate item and
touch the RTN button to switch to the data
input mode.
Adjust the trim rate by scrolling the touch
sensor.
 ,QLWLDOYDOXH
 $GMXVWPHQWUDQJHa
:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV
UHVHWWRWKHLQLWLDOYDOXH