Fyllo f8 - User Manual

Questions and Answers

D
David BrownAug 15, 2025
Why is no coffee brewed by my Fyllo f8 Coffee Maker?
- C
  cschroederAug 15, 2025
  The water tank might be empty. Fill the water tank and follow the first-time use procedure.
W
William LandryAug 18, 2025
What to do if water is leaking at the base of my Fyllo Coffee Maker?
- L
  leeericksonAug 18, 2025
  There are several possible causes: * The water tank might be leaking, in which case you should check if the valve on the water tank is stuck open. * The drip tray might be full. Empty the drip tray. * The drip tray might be missing. Make sure the drip tray is in place.
J
James OneillAug 22, 2025
Why is my Fyllo f8 not hot enough?
- M
  Michael MccormickAug 22, 2025
  The coffee might not be hot enough due to a few reasons: * The cup or mug is cold. Preheat your cup or mug. * There is scale build-up in the machine. Descale the machine. * Brewing a cup of water will pre-heat the machine.
K
kendra46Aug 25, 2025
What to do if my Fyllo Coffee Maker machine does not turn on?
- K
  Kenneth LoganAug 26, 2025
  The machine may not be turning on due to lack of power. Connect the power cord and turn on the machine.
H
hogandavidAug 28, 2025
Why won’t the coffee capsule/pod eject from my Fyllo f8?
- J
  Julie NelsonAug 28, 2025
  The coffee capsule/pod may not eject for the following reasons: * The used coffee pod container is full. Empty the used coffee capsule/pod container. * The coffee pod is deformed after brewing. Push the used capsule with your finger, or use a plastic knife to push the ESE pod down.
J
Joshua TranSep 1, 2025
Why does steam escape when the handle is opened on my Fyllo f8 Coffee Maker?
- C
  cindy35Sep 1, 2025
  If you opened the handle too quickly after brewing, it is normal for some steam to escape. Wait a few seconds after you have finished brewing the coffee to let the residual steam escape.
J
jennifer11Sep 3, 2025
Why does the coffee pod drop directly into the used coffee pod container in my Fyllo Coffee Maker?
- M
  matthewwestSep 4, 2025
  The coffee pod may be deformed. Try it again with a slightly different angle. Use a new coffee capsule/pod or another brand of capsule/pod.
A
adamsdonnaSep 7, 2025
Why does coffee come out in drips or why is the handle hard to open on my Fyllo f8?
- L
  Lindsey ColemanSep 8, 2025
  The ground coffee in the coffee pod might be too fine to pass water. Wait for 3 minutes to open the handle and change to a new coffee pod.
C
Caitlyn PhelpsSep 12, 2025
Why are there occasional drops dripping out of the dispensing head of my Fyllo f8?
- M
  Matthew VargasSep 12, 2025
  Occasional drops are normal, it is not a defect. The internal heater is keeping warm.

The fyllo f8 is an espresso coffee machine designed for household use, offering a compact and user-friendly experience for brewing coffee. It is available in two versions: F8-NES for Nespresso®* capsules and F8-ESE for ESE pods, catering to different coffee preferences.

Function Description:

The fyllo f8 is an espresso coffee machine that allows users to brew coffee using either Nespresso®* compatible capsules or ESE (Easy Serving Espresso) pods, depending on the model. It features two control buttons for brewing espresso and lungo, with programmable coffee volumes to customize the strength and size of your drink. The machine includes an adjustable coffee dispenser spout, a removable water tank, and a drip tray with a container for used capsules/pods. It also incorporates an energy-saving mode and a factory reset function for convenience.

Important Technical Specifications:

Rated Voltage: 220-240V AC
Rated Frequency: 50Hz
Rated Power: 1,260W
Net Weight/Gross Weight: Approximately 3.1/3.5 KG
Pump Pressure: Max. 19 Bars
Water Tank Capacity: 0.8L
Dimensions (WLH): 118mm * 365mm * 250mm
Protection Class: I
Default Coffee Brewing Time: Espresso 25s, Lungo 40s (programmable from 13s to 90s)
Used Capsule/Pod Container Capacity: Approximately 10 used capsules/pods
Model Numbers:
- F8-NESB (Black) / F8-NESW (White) / F8-NESR (White) for Nespresso®* Capsules
- F8-ESEB (Black) / F8-ESEW (White) / F8-ESER (White) for ESE Pods

Usage Features:

First Use and Flushing: Before initial use or after long periods of disuse, the machine must be flushed to clean the internal piping. This involves filling the water tank and running a flush cycle by pressing the lungo button.
Water Tank Filling: The 0.8L water tank can be filled either directly into the machine using a jug or by removing the tank, filling it to the "MAX" mark with cold fresh water, and then reattaching it.
Brewing Coffee:
1. Place an empty cup under the adjustable dispenser.
2. Move the handle up and back completely.
3. Insert an ESE pod or a capsule into the compartment. For ESE pods, slide back the ESE pod cover before insertion.
4. Close the handle firmly.
5. Press the desired coffee button (espresso or lungo) once. The button will blink, and brewing will start, stopping automatically at the default brewing time.
6. Raise the handle to eject the used capsule/pod into the container, then close the handle.
Refilling Internal Circuit: If the water tank runs out during brewing, the process can be stopped by pressing the blinking button. After refilling the tank, the machine should be flushed.
Energy Saving Mode: The machine automatically enters energy-saving mode after 15 minutes of inactivity, indicated by cyclically flashing buttons. Pressing any button will wake the machine up, and it will warm up before being ready to brew.
Programming Coffee Volume:
1. Ensure the water tank is in place.
2. Move the handle back completely.
3. Insert a capsule or ESE pod.
4. Close the handle firmly.
5. Press and hold the desired button. Release the button once the desired coffee volume is reached. The new volume will be recorded for future use. The volume range is controlled by time, from 13 seconds (approx. 25ml) to 90 seconds (approx. 150ml). The blinking frequency of the button (1 blink per second) can be used to estimate brewing time.

Maintenance Features:

Cleaning:
- Emptying Capsule/Pod Container and Drip Tray: The used capsule/pod container holds approximately 10 items. It is recommended to empty it daily. The blue light indicates when the container is full. To empty, raise the handle, raise the dispensing spout (if in low position), pull out the drip tray firmly, dispose of used items, and rinse the drip tray set with fresh water.
- Coffee Machine Cleaning: Always unplug the machine before cleaning. Never immerse the machine in water or clean it under running water. Clean the machine with a dry cloth. Avoid abrasive cleaning agents or materials.
Decalcification: To prevent damage from lime particle build-up, decalcify the machine at least every 300-400 cups of coffee or monthly.
1. Pour a commercially available coffee machine descaling solution (diluted according to manufacturer's instructions) into the water tank.
2. Ensure no capsule/pod is inside the machine.
3. Place a large bowl under the dispensing head.
4. Fill the water tank to maximum level with the descaling solution.
5. Ensure the solution is completely dissolved.
6. Press the small button multiple times to run the entire tank of descaling water through the machine, mimicking normal coffee brewing.
7. Repeat the process with another tank of descaling solution.
8. Finally, flush the internal circuit with a tank of fresh water (without descaling solution) to clean it completely.
Steaming Out/Storage/Transport: Before long periods of disuse or storage/transport at temperatures below 5°C, the machine must be steamed out to remove water and prevent frost damage.
1. Turn on the machine.
2. Empty the water tank and place it back.
3. Place an empty cup under the coffee dispensing spout.
4. Press the "Lungo" button to start steaming out. The process is complete when the pump stops automatically.
5. Turn off and unplug the machine.

Safety Precautions:

Always unplug the machine before relocating, cleaning, maintenance, or long periods of disuse.
Never touch the power plug/socket/cable or machine with damp or wet hands.
Do not operate the machine without water or with water below the minimum level.
Never move the machine during operation.
Beware of hot parts (e.g., brew unit) and hot steam/water jets.
Do not open the handle when the machine is brewing or under pressure.
Do not use the machine if faulty, has a damaged power cable, or has fallen.
Place the machine on a dry, stable, level surface, at least 60 cm away from washbasins and taps, and away from flammable/fusible surfaces or hot surfaces/open flames.
Keep children away from the machine during operation.
This appliance is not intended for use by young children or infirm persons unless adequately supervised.
If the supply cord is damaged, it must be replaced by the manufacturer or a qualified person.
Only use replacement parts or accessories recommended by the manufacturer.

Fyllo f8 Specifications

General

Brand	Fyllo
Model	f8
Category	Coffee Maker
Language	English