Why Gardena Lawn Mower mows for shorter periods?
If your Gardena Lawn Mower is mowing for shorter periods than usual between charges, grass or another foreign object may be blocking the blade disc. Remove and clean the blade disc.
Why Gardena R70Li showing low battery?
If your Gardena Lawn Mower displays 'Low battery', it might not be finding the charging station. Ensure the charging station and guide wire are correctly installed. Also, check if the indicator lamp in the charging station flashes yellow. If the battery is spent, replace it. Check if the charging station's antenna is defective, indicated by a red flashing indicator lamp.
Why does my Gardena R70Li say no loop signal?
A 'no loop signal' error on your Gardena Lawn Mower can occur for several reasons. It could be due to the transformer not being properly connected, so check the wall socket and the connection of the low voltage cable to the charging station. Also, the boundary wire might not be correctly connected to the charging station. In some cases, metal objects or buried cables nearby can cause disturbances; try moving the boundary wire. Finally, the connection between the mower and the charging station might be broken. To fix this, place the mower in the charging station and generate a new loop signal via Security -> New loop signal.
What to do if Gardena R70Li cutting system blocked?
If the cutting system of your Gardena Lawn Mower is blocked, it's likely due to grass or another object wrapped around the blade disc. Check the blade disc and remove any obstructions. Alternatively, the blade disc might be sitting in a pool of water. If this is the case, move the mower and try to prevent water from collecting in that area.
Why does my Gardena Lawn Mower go outside working area?
If your Gardena Lawn Mower is showing 'Outside working area', make sure the boundary wire connections to the charging station are correct. Also, ensure the boundary wire isn't too close to the edge or laid incorrectly around an island. If there are disturbances from metal objects or buried cables, try moving the boundary wire. If the robotic lawnmower finds it hard to distinguish the signal from another robotic lawnmower installation close by, place the robotic lawnmower in the charging station and generate a new loop signal via Security -> New loop signal. Check if the working area slopes too much.
How to prevent breaks in the Gardena R70Li Lawn Mower loop wire?
Breaks in the loop wire are usually the result of unconscious physical damage to the wire such as when gardening with a shovel. To avoid this, always select the maximum cutting height the first weeks after installation and then lower the height one step at a time every second week until the desired cutting height has been reached. A defective splicing of the loop wire can also lead to disruptions first several weeks after the splice was done. Please first check all known splices before further troubleshooting is done.
What to do if my Gardena Lawn Mower shows 'No loop signal'?
If your Gardena Lawn Mower displays 'No loop signal', there could be several reasons. First, ensure the transformer is properly connected to the wall socket and that the low voltage cable is connected to the charging station. Also, check the boundary wire connection to the charging station. If the boundary wire is broken, locate the break and replace the damaged section using an original coupler. Verify the boundary wire isn't laid incorrectly around an island, and if disturbances from metal objects or buried cables are present, try moving the boundary wire. If the connection between the lawnmower and charging station is broken, place the lawnmower in the charging station and generate a new loop signal via Security -> New loop signal.
What to do if Gardena R70Li Lawn Mower is stuck in charging station?
If your Gardena Lawn Mower is stuck in the charging station, there is likely an object preventing it from leaving. Remove the object.
Why Gardena Lawn Mower has difficulty docking?
If your Gardena Lawn Mower is having trouble docking, it could be due to a few reasons. The boundary wire might not be laid in a long, straight line far enough out from the charging station. Also, the guide wire might not be inserted in the slot at the bottom of the charging station, it is absolutely critical for operation that the guide wire is perfectly straight and is in the correct position under the charging station. Finally, the charging station itself might be on a slope. Ensure the charging station is placed on a completely level surface.
What to do if Gardena Lawn Mower charging station is blocked?
If the charging station of your Gardena Lawn Mower is blocked, it might be because the contact between the charging strips and contact strips is poor, causing the mower to make repeated charging attempts. Ensure the mower is properly placed in the charging station and that the charging strips and contact strips make good contact. Alternatively, an object might be obstructing the mower; remove any such object.
General| Type | Robotic lawn mower |
|---|---|
| Cutting width | 170 mm |
| Cutting height | 50 mm |
| Cutting system | - |
| Recommended lawn area | 700 m² |
| Minimum cutting height | 20 mm |
| Grass collecting volume | - L |
| Power source | Battery |
| Charging time | 1.16 h |
| Cordless | Yes |
Weight and Dimensions| Weight | 7500 g |
|---|
To Next Page
