Garrett AT Gold - User Manual

Questions and Answers

D
David PenaJul 26, 2025
Why does my Garrett AT Gold Metal Detector make erratic sounds?
- N
  Natalie JoyceJul 26, 2025
  Erratic sounds or target ID cursor movement can occur if you are using the Garrett Metal Detector indoors because of excessive electrical interference and metal in floors and walls. Ensure your searchcoil is securely connected and the coil cable is snugly wound around the stem. Also, check if you are near power lines, wire fences, or other metal structures. Try adjusting the frequency or reducing the sensitivity setting.
D
Daniel ChavezJul 30, 2025
Why am I not finding specific targets with my Garrett AT Gold?
- D
  Dr. Megan RossJul 31, 2025
  If you are not finding specific targets with your Garrett Metal Detector, ensure you are using the correct mode for the type hunting you are doing. If specifically hunting for U.S. coins, DISC 2 mode should be your best choice to eliminate other undesirable targets. The ALL METAL or DISC 1 modes will detect all metal targets to ensure desired targets are detected.
M
Marilyn WardAug 3, 2025
How to fix a Garrett AT Gold with no power?
- L
  Lori MendozaAug 3, 2025
  If your Garrett Metal Detector has no power, ensure batteries are installed in the correct position and replace all old batteries with all new batteries.
M
Michael McknightAug 8, 2025
What causes intermittent signals on my Garrett Metal Detector?
- L
  lynn36Aug 8, 2025
  Intermittent signals on your Garrett Metal Detector usually indicate a deeply buried target or one positioned at a difficult angle. You can try scanning from different directions to better define the signal. Remember that iron targets can also cause intermittent signals; use the Iron Audio feature to help identify them.
A
Alicia ThompsonAug 12, 2025
Why does my Garrett AT Gold Metal Detector make erratic sounds or show erratic target ID cursor movement?
- L
  Lisa BuchananAug 12, 2025
  Erratic sounds or target ID cursor movement can occur due to several reasons. Ensure your searchcoil is securely connected and the coil cable is snugly wound around the stem. If you are using the detector indoors, be aware that excessive amounts of electrical interference exists, plus excessive amounts of metal can be found in floors and walls. Determine if you are close to other metal detectors or other metal structures such as electrical power lines, wire fences, benches, etc. You can also try adjusting the frequency or reducing your sensitivity setting.
N
nnicholsAug 16, 2025
What to do if the Target ID Cursor bounces on my Garrett Metal Detector?
- A
  Amber PowellAug 17, 2025
  If your Garrett Metal Detector's Target ID Cursor bounces erratically, it is likely you've found an iron target. A Target ID Cursor may bounce if a good target (such as a coin) is not parallel to the searchcoil. It may also bounce if there is one or multiple “junk” targets laying next to the good target. Try scanning from different directions until your Target ID Cursor becomes more stable. You can use the Iron Audio feature to help identify iron targets, especially large, flat pieces of iron.
D
Deborah MontoyaAug 20, 2025
What to do if my Garrett AT Gold Metal Detector has intermittent signals?
- J
  Joseph DanielAug 21, 2025
  If you are getting intermittent signals on your Garrett Metal Detector, it may be due to a deeply buried target or difficult angle. Try scanning from different directions to help define the signal.

Summary

AT GOLD CONTROL PANEL

QUICK START GUIDE

ASSEMBLY AND COMPONENTS

List of Parts

Lists all components included with the metal detector.

BASIC OPERATION

Powering On and Target ID

Instructions for turning the detector on and understanding target identification displays.

Ground Balance and Sensitivity

Setting sensitivity and performing ground balance for optimal detection in varied soils.

DETECTION MODES AND FEATURES

All Metal Mode

True all-metal detection for maximum depth and sensitivity, detecting all metal types.

Discrimination Modes

Modes to eliminate unwanted targets and provide target identification, offering more audio information.

Iron Discrimination and Audio

Techniques for identifying and rejecting iron targets using discrimination and audio features.

OPERATING TECHNIQUES

Searchcoil Sweeping

Guidelines for proper searchcoil movement for effective target detection.

Pinpointing Targets

Methods for accurately locating detected targets using the pinpoint function.

ADVANCED TIPS AND SPECIALIZED USE

Ground Mineralization and Interference

Strategies for handling mineralized ground, hot rocks, and other interference.

Prospecting and Underwater Use

Tips for gold prospecting and guidelines for operating the detector in water.

CARE, TROUBLESHOOTING, AND WARRANTY

Care and Maintenance

Procedures for cleaning, storing, and maintaining the detector for longevity.

Troubleshooting Guide

Solutions for common problems encountered with the metal detector.

Cautions and Warranty

Important safety precautions, warnings, and warranty service information.

Garrett AT Gold Specifications

General

Operating Frequency	18 kHz
Search Modes	3 (All Metal, Discrim 1, Discrim 2)
Iron Audio	Yes
Ground Balance	Automatic and Manual
Audio Tone ID Levels	3
Battery	4 AA (included)
Pinpointing	Yes
Sensitivity Adjustment	Yes
Waterproof	Up to 10 feet (3 meters)
Target ID	0-99
Weight	2.8 lbs
Headphones	Included
Warranty	2 years
Battery Life	20-30 hours
Coil Size	5" x 8" PROformance™ DD submersible search coil