GE B30 UR Series - Page 581

GE Multilin B30 Bus Differential System vii
INDEX
RS232
configuration ................................................................. 1-10
specifications ................................................................ 2-15
wiring............................................................................ 3-22
RS422
configuration ................................................................. 3-33
timing............................................................................ 3-34
two-channel application ................................................. 3-33
with fiber interface ......................................................... 3-35
RS485
configuration ................................................................... 1-8
description .................................................................... 3-24
specifications ................................................................ 2-15
RTD INPUTS
actual values ................................................................. 6-17
Modbus registers .................................................. B-18, B-32
settings ....................................................................... 5-196
specifications ................................................................ 2-13
S
SALES OFFICE ................................................................. 1-2
SATURATION DETECTOR ................................................. 9-8
SAVING SETTING DOES NOT TAKE RELAY OUT OF SERVICE
5-9
SCAN OPERATION............................................................ 1-4
SECURITY ............................................................... 5-12, 9-6
delete files and records ................................................. 11-7
SELECTOR SWITCH
actual values ................................................................... 6-6
application example..................................................... 5-161
FlexLogic operands ..................................................... 5-105
logic............................................................................ 5-162
Modbus registers ........................................................... B-46
settings ....................................................................... 5-157
specifications ................................................................ 2-12
timing................................................................ 5-160, 5-161
Self-test errors................................................................... 7-9
SELF-TESTS
description ...................................................................... 7-4
error messages ............................................................... 7-5
FlexLogic operands ..................................................... 5-107
Modbus registers .............................................................B-9
SERIAL NUMBER ............................................................ 6-20
SERIAL PORTS
Modbus registers ........................................................... B-25
settings ......................................................................... 5-21
SERVICE LIFE EXPECTED .............................................. 1-19
SETTING GROUPS.......................... 5-105, 5-121, 5-155, B-36
SETTINGS
change does not take relay out of service ......................... 5-9
SETTINGS FILE................................................................. 4-1
takes relay out of service when loaded ............................. 4-2
SETTINGS TEMPLATES
description ...................................................................... 4-5
editing............................................................................. 4-5
enabling .......................................................................... 4-5
Modbus registers ........................................................... B-68
password protection ........................................................ 4-6
removing ......................................................................... 4-8
viewing ........................................................................... 4-7
SETTINGS, CHANGING ................................................... 4-26
SIGNAL LOSS DETECTION FOR FIBER........................... 5-25
SIGNAL SOURCES
description ...................................................................... 5-5
metering........................................................................ 6-14
SIGNAL TYPES..................................................................1-4
SINGLE LINE DIAGRAM..............................................2-1, 2-2
SITE LIST, CREATING .......................................................4-1
SNTP PROTOCOL
accuracy........................................................................2-15
error messages................................................................7-7
Modbus registers .......................................................... B-27
settings .........................................................................5-51
SOFTWARE
installation .......................................................................1-6
see entry for ENERVISTA UR SETUP
SOFTWARE ARCHITECTURE ............................................1-4
SOFTWARE, PC
see entry for EnerVista UR Setup
SOURCE FREQUENCY ....................................................6-16
SOURCE TRANSFER SCHEMES.................................... 5-148
SOURCES
description.......................................................................5-5
example use of ..............................................................5-83
metering ........................................................................6-14
Modbus registers ................................................. B-13, B-30
settings .........................................................................5-82
SPECIFICATIONS ............................................................2-10
STANDARD ABBREVIATIONS ............................................F-5
STATUS INDICATORS ............................................ 4-15, 4-17
STORAGE........................................................................11-9
STORAGE TEMPERATURE ..............................................2-16
SUMMATOR
Modbus registers .......................................................... B-40
SURGE IMMUNITY...........................................................2-17
SYMMETRICAL COMPONENTS METERING .....................6-11
SYNCHROCHECK
actual values .......................................................... 6-9, 6-17
SYNCHROPHASORS
commands .......................................................................7-3
SYSLOG ..........................................................................5-18
SYSTEM FREQUENCY.....................................................5-81
SYSTEM LOGS ................................................................5-18
SYSTEM REQUIREMENTS.................................................1-6
SYSTEM SETUP ..............................................................5-80
T
TARGET MESSAGES .........................................................7-4
TARGET SETTING .............................................................5-5
TARGETS MENU ...............................................................7-4
TCP PORT NUMBER ........................................................5-43
TELEPROTECTION
actual values ...................................................................6-4
clearing counters .............................................................7-2
FlexLogic operands ...................................................... 5-105
logic ............................................................................ 5-192
Modbus registers ................................................. B-45, B-46
overview ...................................................................... 5-191
settings ....................................................5-77, 5-191, 5-192
specifications.................................................................2-13
TEMPERATURE MONITOR ..................................... 5-107, 7-8
TERMINALS.......................................................................3-7
TESTING
force contact inputs...................................................... 5-202
force contact outputs.................................................... 5-203
lamp test .........................................................................7-3
self-test error messages...................................................7-4
THEORY OF OPERATION ..................................................9-1