GE M60 UR Series

To Next Page

833711A2.CDR

M60 Revision: 7.2x

Manual P/N: 1601-0108-AA1 (GEK-119565)

M60 Motor Protection System

UR Series Instruction Manual

GE Digital Energy

650 Markland Street

Markham, Ontario

Canada L6C 0M1

Tel: +1 905 927 7070 Fax: +1 905 927 5098

Internet: http://www.GEDigitalEnergy.com

GE Multilin's Quality Management

System is registered to ISO

9001:2008

QMI # 005094

UL # A3775

*1601-0108-AA1*

LISTED

52TL

IND.CONT. EQ.

E83849

Digital Energy

Main Page

Default Chapter3
- Table of Contents3
1 Getting Started11
- Important Procedures11
  - Cautions and Warnings11
  - Inspection Procedure12
- Ur Overview13
- Enervista Ur Setup Software15
- Ur Hardware27
- Using the Relay28
2 Product Description31
- Introduction31
- Order Codes38
- Specifications47
3 Hardware59
- Description59
  - Panel Cutout59
  - Rear Terminal Layout64
- Wiring66
- Direct Input/Output Communications83
4 Human Interfaces99
- Enervista Ur Setup Software Interface99
- Extended Enervista Ur Setup Features102
- Faceplate Interface111
5 Settings125
- Overview129
- Product Setup136
- System Setup225
- Flexlogic246
- Grouped Elements268
- Control Elements343
- Inputs and Outputs379
- Transducer Inputs and Outputs396
- Testing 5.10.1 Test Mode409
  - Force Contact Inputs409
  - Force Contact Outputs409
6 Actual Values411
- Overview411
  - Actual Values Menu411
- Status411
- Records435
- Product Information439
  - Model Information439
  - Firmware Revisions439
7 Commands and441
- Commands441
- Targets445
8 Commissioning453
- Testing453
  - Testing Underfrequency and Overfrequency Elements453
9 Maintenance455
- Modules455
  - Replace a Module455
- Batteries457
  - Replace Battery457
  - Dispose of Battery459
Parameter Lists463
- Flexanalog Items463
- A.1.1 Flexanalog Items463
- Flexinteger Items473
- A.1.2 Flexinteger Items473
Modbus Communications475
Modbus Rtu Protocol475
- Introduction475
- Physical Layer475
- Data Link Layer475
- B.1.1 Introduction475
- Algorithm476
- B.1.4 Crc-16 Algorithm476
Modbus Function Codes477
- Supported Function Codes477
- Read Actual Values or Settings (Function Code 03/04H477
- Execute Operation (Function Code 05H478
- Store Single Setting (Function Code 06H478
- Store Multiple Settings (Function Code 10H479
- Exception Responses479
File Transfers480
- Obtaining Relay Files Via Modbus480
- Modbus Password Operation481
Memory Mapping482
- Modbus Memory Map482
- Data Formats548
- B.4.2 Data Formats548
Iec 61850585
Overview585
- Introduction585
- Communication Profiles585
- C.1.1 Introduction585
Server Data Organization586
- Overview586
- Ggio1: Digital Status Values586
- Ggio2: Digital Control Values586
- Ggio3: Digital Status and Analog Values from Goose Data586
- Ggio4: Generic Analog Measured Values586
- C.2.1 Overview586
- Mmxu: Analog Measured Values587
- Protection and Other Logical Nodes587
Server Features and Configuration589
- Buffered/Unbuffered Reporting589
- File Transfer589
- Timestamps and Scanning589
- Logical Device Name589
- Location589
- Logical Node Name Prefixes590
- Connection Timing590
- Non-Iec 61850 Data590
- Communication Software Utilities590
Generic Substation Event Services: Gsse and Goose591
- Overview591
- Gsse Configuration591
- Fixed Goose591
- Configurable Goose591
- C.4.1 Overview591
- Ethernet Mac Address for Gsse/Goose594
- Gsse ID and Goose ID Settings594
Iec 61850 Implementation Via Enervista Ur Setup595
- Overview595
- C.5.1 Overview595
- Configuring Iec 61850 Settings596
- About ICD Files597
- Creating an ICD File with Enervista Ur Setup601
- About Scd Files601
- Importing an Scd File with Enervista Ur Setup604
Acsi Conformance606
- Acsi Basic Conformance Statement606
- Acsi Models Conformance Statement606
- Acsi Services Conformance Statement607
Logical Nodes610
- Logical Nodes Table610
Iec 60870-5-103615
- Overview615
- D.1.1 Overview615
- Interoperability Document616
- D.1.3 Interoperability Document616
Iec 60870-5-104 Protocol621
- Interoperability Document621
- E.1.1 Interoperability Document621
- Point List629
- E.1.2 Point List629
Device Profile Document631
- Dnp V3.00 Device Profile631
- F.1.2 Implementation Table634
Dnp Point Lists638
- Binary Input Points638
- Binary and Control Relay Output639
- Counters640
- F.2.3 Counters640
- Analog Inputs641
- F.2.4 Analog Inputs641
Radius Server Configuration643
- Revision History645
- H.1.1 Revision History645
- Changes to the M60 Manual646
Abbreviations649
- Standard Abbreviations649
  - H.2.1 Standard Abbreviations649
  - H.3.1 Ge Multilin Warranty651
Warranty652

Need help?

Do you have a question about the GE M60 UR Series and is the answer not in the manual?

GE M60 UR Series Specifications

General

Type	Feeder Protection Relay
Frequency	50/60 Hz
Communication Protocols	Modbus RTU, Modbus TCP/IP, DNP3, IEC 61850
Display	LCD
Enclosure Rating	IP54
Mounting	Panel Mount
Current Rating	1 A / 5 A
Protection Functions	Overcurrent, Ground Fault, Frequency
Analog Outputs	Up to 2