GE EntelliGuard G - Time Delay Module (TDM) for UVR (Externally Mounted); Remote Operation Coil Combination; Auxiliary Switches

DEH-41304C EntelliGuard® G Circuit Breaker
13 March 14 Section 6 – Accessories Description
©2012 General Electric All Rights Reserved 29
Table 6.5. UVR Operating Characteristics
Power
Consumption
Nominal Control
Voltage
Catalog
Number
DC: 350 W,
20 W (sealed)
AC: 350 W
(inrush),
20 W (sealed)
24/30 Vdc
GUVT030DR
40 Vdc; 48 Vac/dc
GUVT048R
60 Vdc
GUVTO60DR
110/130/120 Vac
GUVT130R
208 Vac
GUVT208AR
220 Vdc/240 Vac
GUVT240R
250 Vdc/277 Vac
GUVT277R
 Duty cycle = 2/min.
 Inrush = 350 VA (ac), 350 W (dc).
 Holding = 60 VA (ac), 50 W (dc).
Time Delay Module (TDM) for UVR (Externally Mounted)
The de-energized operation of the Under Voltage release can
be delayed. This optional, externally mounted module has an
adjustable time delay of 0 s to 3 s. The device can be
implemented to prevent undesired breaker tripping due to
momentary voltage interruptions and is connected in series
with the Under Voltage release. The time delay is in addition
to the time delay from the breaker mounted UVR accessory.
The time delay module starts counting at 50% of rated
voltage (Fig. 6.2 and Table 6.6).
Figure 6.2. Time Delay Module
Table 6.6 TDM Characteristics
Nominal Control Voltage
Catalog No.
48VDC
GTDM048D
48VAC
GTDM048A
60VDC
GTDM060D
120VDC
GTDM120D
120VAC
GTDM120A
208VAC
GTDM208A
240VDC
GTDM240D
240VAC
GTDM240A
250VDC
GTDM250D
277VAC
GTDM277A
Remote Operation Coil Combination
Each breaker accepts a maximum of four coils in the
combinations shown in Table 6.7. All coils are mounted from
the front and snap onto the mechanism after the fascia is
removed.
Table 6.7. Remote Operation Coil Combination
Combination
Coil Position on Fascia (from left)
1
2
3
4
1
-
shunt
CC
UV
2
shunt
shunt
CC
UV
3
shunt
UV
CC
UV
Auxiliary Switches
Auxiliary switches indicate breaker main contact position.
They change their state in the same time sequence as the
breaker main contacts. See Tables 6.8 and 6.9 for available
combinations and ratings.
Table 6.8. Auxiliary Switches
Contact Configuration
Cat. No.
Power rated (3NO+3NC)
GAUX3R
Power rated (3NO+3NC) + low signal (Hi-Fi)
(2NO+2NC)
GAUX5R
Power rated (8NO+8NC)
GAUX6R
Power rated (4NO+4NC) + low signal (Hi-Fi)
(4NO+4NC)
GAUX8R
Table 6.9. Auxiliary Switch Ratings and Secondary
Disconnect Points
Contact Configuration
Power
Rated
Hi-Fi
Cat. No.
Power rated
(3NO+3NC)
A14 - A25
N/A
GAUX3R
Power rated (3NO+3NC) +
low signal (Hi-Fi)
(2NO+2NC)
A14 - A25
B10 - B13,
B23 - B26
GAUX5R
Power rated
(8NO+8NC)*
A14 - A25,
B4 - B13,
B17 - B26
N/A
GAUX6R
Power rated (4NO+4NC) +
low signal (Hi-Fi)
(4NO+4NC)*
A14 - A25,
B12 - B13,
B25 - B26
B4 - B11,
B17 - B24
GAUX8R
*Options are not available for side mounted sec disc blocks.
 High Fidelity refers to gold-plated contacts. Use for signal level outputs
(10 mA min to 100 mA max., 8 Vdc to 30 Vdc, 125 Vac.
Courtesy of store.ips.us