NX-8 Control
24
L LOCATION 40 - SYSTEM TIMERS (10 segments, numerical data)
Location 40 contains the duration of various system timing functions. Example: If you desire the duration of the
Dynamic Battery Test to be 30 minutes, you should program [3]-[0]-[r] in segment 1 of this location. The [3]-[0] is the
number of minutes, and the [r] stores the data and moves to the next segment of this location.
Segment 1 Dynamic Battery Test duration in minutes (0-255 minutes). Factory default is 0 = no test.
Segment 2 AC Fail report delay in minutes 0-255 minutes. Factory default is 5.
Segment 3 Power Up Delay in seconds (0-60 seconds). Factory default is 60.
Segment 4 Siren Time in minutes (1-254 minutes). Factory default is 8.
Segment 5 Telephone Line Cut delay in seconds (0-255 seconds). Factory default is 0 = no TLM.
Segment 6 Cross Zone time in minutes (0-255 minutes). Factory default is 5.
Segment 7 Chime time in 50 mS (1/20th second) increments from 0-12 seconds (0 = follows zone 255
latched). Factory default is 3.
Segment 8 Dialer delay in seconds (15-255 seconds). Factory default is 30.
Segment 9 Fire Alarm Verification time in seconds (120-255 seconds). Factory default is 0 = no fire alarm
verification. NOTE: This feature is not approved for residential use in California
Segment 10 Listen-In time in seconds (0-255 seconds). Factory default is 0 = no Listen-In time.
Note for UL LISTED SYSTEMS: The "Listen-In" feature cannot be enabled. The "Dynamic Battery Test"
feature cannot exceed four (4) hours. The dial delay shall be set to -0-.
LOCATION 41 - SPECIAL FEATURES (1 segment, feature selection data)
Segment 1:
1 - On enables the 6-digit code option. If 6-digit option is enabled, all arm/disarm codes and the "Go To
Program Code" are 6 digits. If this option is enabled, the default user 1 code is [1]-[2]-[3]-[4]-[5]-[6].
NOTE: IF YOU ENABLE THIS OPTION, VERIFY THAT THE "GO TO PROGRAM CODE" IS A
SIX-DIGIT CODE BEFORE EXITING PROGRAMMING.
2 - On requires code entry for [r]-[9]-[8] (perform call back download) and [r]-[9]-[9] (answer incoming
call for download) functions.
3 - Enable Auto Cancel / Abort (Refer to feature definitions beginning on page 5)
4 - Enable Walk-Test Mode (Refer to feature definitions beginning on page 5)
5-8 Reserved.
L LOCATION 42 - GO TO PROGRAM CODE (6 segments, numerical data)
Location 42 contains the "Go To Program Code". This location contains either a 4 or 6-digit code. If the 6-digit code
option is enabled in Location 41, THIS CODE MUST CONTAIN SIX (6) DIGITS. If this option is not enabled in
location 41, the last 2 segments (digits) will be ignored. With the NX-8 disarmed, the "Go To Program Code" can be
used to enter the Program Mode.
LOCATION 43 - GO TO PROGRAM CODE PARTITION AND AUTHORIZATION (2 segments, feature selection)
The "Go To Program Code" can be used as a standard arm/disarm code. When using the code to arm or disarm, the
user ID is 255. (This code may not be changed in the Run Mode.)
Segment 1: 1 - Reserved.
2 - On enables "Go To Program Code" as an arm only code.
3 - On enables "Go To Program Code" as an arm only after closing.
4 - On enables "Go To Program Code" as a master arm/disarm code (can change user codes)
5 - On enables "Go To Program Code" as an arm/disarm code.
6 - On enables "Go To Program Code" to bypass zones.
7 - On enables "Go To Program Code" opening and closing reports.
8 - Reserved.
Segment 2: 1 - On enables the "Go To Program Code" for Partition #1.
2 - On enables the "Go To Program Code" for Partition #2.
3 - On enables the "Go To Program Code" for Partition #3.
4 - On enables the "Go To Program Code" for Partition #4.
5 - On enables the "Go To Program Code" for Partition #5.
6 - On enables the "Go To Program Code" for Partition #6.
7 - On enables the "Go To Program Code" for Partition #7.
8 - On enables the "Go To Program Code" for Partition #8.
To Next Page
Loading...
