What to do if temperature monitoring is not working as expected on GE Xcellerex XDUO 200 Mixer?
If temperature monitoring is not working as expected: * Switch to the second input of the temperature probe if possible. If the second input is not present or is not working, replace the probe. * Ensure the temperature probe is inserted into the thermowell.
What to do if the agitator does not start on GE Xcellerex XDUO 200?
If the agitator does not start, consider the following: * Check if the Min Weight interlock is active. Check the weight of the disposable bag. * If the system is in the state of E- STOP, tap RESET on the local control software home screen and start the agitator when the system has been restarted after emergency shutdown. Note: The agitator cannot be started while the system is in the state E-STOP.
What to do if agitator motor cannot be started on GE Mixer?
If the agitator motor cannot be started, check the following: * Ensure the power switch on the I/O Cabinet is in the I ON position. * Verify the power cable is connected. * If the issue persists, the drive may be broken, and you should contact your GE representative to replace it.
Why is variable frequency drive (VFD) not functioning as expected in GE Mixer?
The variable frequency drive (VFD) might not be functioning as expected due to: * The motor being overloaded. Acknowledge the agitator fault and attempt to restart the motor. If the error persists, contact GE for service. * The power cable not being connected. Connect the power cable. * The drive is broken. Contact your GE representative to replace the drive.
What to do if agitator does not start on FlexFactory controlled GE Mixer?
If the agitator does not start on a FlexFactory controlled mixer: * Enable the agitator. * Tap RESET on the local control software screen and start the agitator when the system has been restarted after emergency shutdown. Note: The agitator cannot be started while the system is in the state E-STOP. * If the system is in Manual mode, set the system to Auto mode and specify the setpoint. Note: When the system is in Manual mode the setpoint is ignored.
What to do if weight monitoring error occurs on GE Xcellerex XDUO 200?
If you encounter a weight monitoring error, such as a weight display outside the operational range or a weight alarm triggered when the mixer weight is within range, consider the following: * Contact the metrology department to perform a cornering test to determine if a load cell has failed. * Check for any physical obstructions that may be hindering the load cell's motion. Ensure the mixer vessel legs are free. * Disengage the jacking bolt. Note that inaccurate weight measurements can occur if the mixer was filled while the jacking bolt was engaged. * Contact your GE representative if you suspect the weight transmitter configuration is incorrect or corrupt.
What to do if load cell is not functioning as expected on GE Xcellerex XDUO 200?
If the load cell is not functioning as expected, consider the following: * Ensure the load cell is properly connected. * Contact the metrology department to perform a cornering test to determine if a load cell has failed. * Verify that there are no physical obstructions blocking the load cell's motion. * Disengage the jacking bolt. Note that weight measurements are inaccurate if the mixer was filled while the jacking bolt was engaged. * Contact your GE representative if you suspect the configuration on the load cell transmitter is incorrect or corrupt. * Schedule a calibration of the load cells.
General| Type | Single-use mixer |
|---|---|
| Nominal Volume | 200 L |
| Material (Biocontainer) | Polyethylene |
| Biocontainer Volume | 200 L |
| Capacity | 200 L |
| Power Requirements | 50/60 Hz |
| Material | Stainless steel |
Crucial safety, intended use, and prerequisite information for users.
Covers general, personal, installation, environmental, and maintenance safety.
Details emergency shutdown and power/communication failure protocols.
Details safety systems like emergency stop, labeling, burst disc, interlocks, and fuses.
Overview of XDUO local control software, home screen, and variable displays.
Details safety warnings for installation: PPE, electrical, magnets, power.
Guides on moving, electrical installation, and configuring local control software.
Safety measures for preparation: PPE, magnets, general cautions.
Guides on unpacking, inspecting, and installing the disposable bag assembly.
Details on preparing, calibrating, and installing pH, conductivity, and temperature probes.
Safety measures during operation: substances, ventilation, hot surfaces, pinch hazards.
Guides on starting, operating agitator, and monitoring parameters for XDM mixer.
Instructions for starting, controlling agitator, pumps, pH, temperature, and weight.
Safety guidelines for maintenance: trained personnel, electrical safety, contamination.
Details the recommended Lock-Out/Tag-Out procedure for turning off the mixer.
Details the recommended Lock-Out/Tag-Out procedure for turning on the mixer.
Troubleshooting for XDM mixer agitation problems like VFD and motor faults.
Troubleshooting XDUO agitation: interlocks, E-STOP, manual mode, alignment.
Troubleshooting XDUO pH control: equilibrium, deadband, PID parameters, and reagents.
To Next Page
