Figure 5. The curves above show the effect of the 'treble tilt', 'bass
tilt' and 'bass roll-off' controls on the free field response.
Figure 6. The upper curve group shows the horizontal directivity
characteristics of the 1030A measured at 1m. The lower curve is the
1/3 octave band power response.
SYSTEMSYSTEM
SYSTEMSYSTEM
SYSTEM
SPECIFICATIONSSPECIFICATIONS
SPECIFICATIONSSPECIFICATIONS
SPECIFICATIONS
AMPLIFIERAMPLIFIER
AMPLIFIERAMPLIFIER
AMPLIFIER
SECTIONSECTION
SECTIONSECTION
SECTION
Lower cut-off frequency, -3 dB: < 52 Hz
Upper cut-off frequency, -3 dB: > 20 kHz
Free field frequency response of system:
55 Hz - 18 kHz (± 2.5 dB)
Maximum short term sine wave acoustic
output on axis in half space, averaged from
100 Hz to 3 kHz:
@ 1m > 105 dB SPL
@ 0.5m > 111 dB SPL
Maximum long term RMS acoustic output in
same conditions with IEC weighted noise
(limited by driver unit protection circuit):
@ 1m > 99 dB SPL
@ 0.5m > 105 dB SPL
Maximum peak acoustic output per pair on
top of console, @ 1 m from the engineer
with music material: > 115 dB
Self generated noise level in
free field @ 1m on axis: < 10 dB
(A-weighted)
Harmonic distortion at 90 dB SPL @ 1m on
axis:
Freq: 60...150 Hz < 3%
> 150 Hz < 0.5%
Drivers: Bass 170 mm (6
1
/
2
") cone
Treble 19 mm (
3
/
4
") metal
dome
Both drivers are magnetically shielded.
Weight: 7,6 kg (17 lb)
Dimensions:
Height 312 mm (12
1
/
4
")
Width 200 mm ( 7
7
/
8
")
Depth 240 mm (9
7
/
16
")
Input connector: XLR female pin 1 gnd
pin 2 +
pin 3 -
Input impedance: 10 kOhm balanced
Input level for 100 dB SPL output @ 1m:
variable from +6 to -6 dBu
Input level for maximum short term sine
wave output of 105 dB SPL @ 1m:
variable from +11 to -1 dBu
Subsonic filter below 50 Hz :
18 dB/octave
Ultrasonic filter above 25 kHz:
12 dB/octave
Crossover frequency, Bass/Treble: 3.5 kHz
Crossover acoustical slopes:
24 - 32 dB/octave
Treble tilt control operating range in 2 dB
steps: from +2 to -4 dB &MUTE
Bass roll-off control operating range in 2 dB
steps: from 0 to -8 dB @ 50 Hz
Bass tilt control operating range in 2 dB
steps: from 0 to -6 dB @ 100 Hz
& MUTE
The 'CAL' position is with all tone controls
set to 'off' and the input sensitivity control to
maximum (fully clockwise).
CROSSOVERCROSSOVER
CROSSOVERCROSSOVER
CROSSOVER
SECTIONSECTION
SECTIONSECTION
SECTION
Bass amplifier output power with a 4 Ohm
load:
Short term 80 W
Treble amplifier output power with an
8 Ohm load:
Short term 50 W
Long term output power is limited by
driver unit protection circuitry.
Amplifier system distortion at
nominal output:
THD < 0.08%
SMPTE-IM < 0.08%
CCIF-IM < 0.08%
DIM 100 < 0.08%
Signal to Noise ratio, referred to full
output:
Bass > 95 dB
Treble > 95 dB
Mains voltage: 100/200 or 115/230 V
Voltage operating range: ±10%
Power consumption:
Idle 20 VA
Full output 100 VA
Genelec Oy, Olvitie 5
FIN - 74100 IISALMI, FINLAND
Phone: +358 - 17 - 83 881
Fax: +358 - 17 - 812 267
E-mail: genelec@genelec.com
Web: http://www.genelec.com
Note! All frequency response curves were measured in
a calibrated, 12 m cube, anechoic chamber at 1 m
using grade 1 measuring equipment. Input signal levels
were set at -20 dBu. The anechoic chamber error in the
free field response is less than 0.5 dB down to 60 Hz.
Data Sheet No. DR30001
COPYRIGHT GENELEC OY 6/1999
All data subject to change without prior notice
Genelec Inc, 7 Tech Circle
Natick, MA 01760, USA
Phone: +1 - 508/652-0900
Fax: +1 - 508/652-0909
E-mail: genelec.usa@genelec.com
To Previous Page
Loading...
Need help?
General
