Genie 7035-TKV User Manual (English)

Questions and Answers:

M
Michael OrrAug 17, 2025
What to do if Genie Garage Door Opener doesn't work with wall control?
- P
  Paul SmithAug 17, 2025
  If your Genie Garage Door Opener doesn't respond to the wall control, try the following: * Turn Sure-Lock™ OFF. * Check the power source by plugging a lamp into the outlet used for the powerhead. If the lamp works, the power source is OK. If not, check the fuse or circuit breaker. * If the power source is working, check the connections at the powerhead terminals and at the wall console. * Inspect the wiring for any reversed, broken, or cut wires. Repair or replace any damaged wires, as staples can sometimes cut the insulation and short the wires.
T
taylordavidAug 20, 2025
How to fix Genie 7035-TKV Garage Door Opener that works with wall control but not remote?
- W
  William WangAug 20, 2025
  If your Genie garage door opener operates with the wall control but not the remote, here are a few things to try: * Check all remotes. * Replace the remote battery. * Program the remotes to the powerhead.
B
brian74Aug 22, 2025
Why is my Genie 7035-TKV Garage Door Opener running slowly?
- Q
  qjonesAug 22, 2025
  If your Genie door opener is running slowly: * Check the operating condition of the door. The door may need professional repair or adjustment. * Verify that the opener is not installed on a one-piece door, as it is not designed for this type of door.
S
Sharon ArmstrongAug 25, 2025
Why does my Genie Garage Door Opener remote have short range?
- P
  Paul BeckAug 26, 2025
  If your Genie garage door opener remote has a limited operating range or isn't working at all, consider these solutions: * Try relocating the remote inside your car and/or point it directly at the garage door. * Replace the remote battery. * Reposition the door opener antenna. * Identify and eliminate any potential competing signals from other devices (like radios). * Be aware that LED bulbs might interfere with the remote signal.
T
Travis StaffordAug 27, 2025
What to do if Genie Garage Door Opener door stops and goes back up?
- J
  James CastroAug 28, 2025
  If your Genie garage door starts to close but then stops and goes back up, or if there's a Safe-T-Beam® System malfunction, try these steps: * If it's a new installation, verify the Door Arm position. * If it's a new installation, ensure that ONLY the Safe-T-Beams® that came with the opener are installed. * Check the limit settings and adjust them if needed. * See if the Safe-T-Beam® red LED is flashing. * Check the Safe-T-Beam® system for any beam obstruction or misalignment of the lenses. * Check the garage door for any binding. * As a temporary solution, press and hold the wall control button until the door is completely closed. * Check for interference from adjacent Safe-T-Beam® units.
D
Dorothy Marshall MDAug 30, 2025
Why does my Genie Garage Door Opener stop before closing?
- J
  john68Aug 30, 2025
  If your Genie garage door starts to go down but stops before it fully closes, or if the door will only open, try the following: * Check the Safe-T-Beam® wire connections at the powerhead and at the STBs. * Make sure the limits are properly set, and adjust them if necessary. * Check the CONTACT REVERSE feature. * Inspect the garage door for any binding. * Check the closing “FORCE” control.
M
Mr. Tyler Bryant PhDSep 2, 2025
Why does my Genie 7035-TKV Garage Door Opener stop before fully opening?
- S
  Sheila ClarkSep 2, 2025
  If your Genie garage door starts to open but stops before it is completely open, try these solutions: * Check if the limits are properly set and adjust them as needed. * Ensure the door, opener, and springs are in good repair, properly lubricated, and balanced. * Check the closing/opening “FORCE” control.
M
mschwartzSep 5, 2025
What to do if Genie Garage Door Opener runs but the door doesn't move?
- J
  Jessica Garcia MDSep 5, 2025
  If the opener motor of your Genie garage door opener is running, but the door isn't moving, here are a couple of things to check: * Ensure the carriage is engaged with the chain/belt turnbuckle. * Check to make sure the chain/belt is not broken or off its pulley.
M
Mr. Gregory MacdonaldSep 8, 2025
Why does my Genie Garage Door Opener only close?
- S
  Sean HoffmanSep 8, 2025
  If your Genie garage door will only close and not open, here are some things you can check: * Turn Sure-Lock™ OFF. * Check if the limits are properly set. * Check the door balance, condition, and door spring. * Check the opening “FORCE” control.

Genie 7035-TKV Specifications

General

Brand	Genie
Model	7035-TKV
Category	Garage Door Opener
Language	English

Summary

Safety Information

Safety Notifications

Alerts to potential hazards that can kill or hurt you and others.

Important Safety Instructions

Key safety guidelines for operating the garage door opener.

Features

Safety Features Overview

Describes safety mechanisms like Safe-T-Beam and Door Detect systems.

Opener Features Overview

Outlines various functional features of the garage door opener.

Safety Notifications & Instructions

Overview of Potential Hazards

Identifies common hazards associated with garage doors and openers.

Conventions Used in Instructions

Explains symbols and signal words used for hazard communication.

Important Safety Instructions

Detailed safety instructions with hazards, effects, and prevention.

Installation Safety Instructions

Reduce Risk of Severe Injury or Death

Critical instructions to prevent serious injury or death during installation.

Safety & Standard Features

Safety Systems

Details Safe-T-Beam, Door Detect, and Safe-T-Reverse safety functions.

Operational & Connectivity Features

Covers manual release, programming, Intellicode, and battery backup.

Wall Console Operation

Explains the functionality of the wall-mounted control console.

Vehicle Compatibility

Information on HomeLink and Car2U system compatibility.

Opener Programming

Introduction to Programming

Guide to programming for proper door operation and remote device function.

Powerhead Controls Overview

Explains programming buttons and LED indicators on the powerhead.

Programming Down Travel Limit

Steps to set the door's fully closed position.

Programming Up Travel Limit

Steps to set the door's fully open position.

Programming Force and Contact Reverse

Setting force controls and testing the safety reverse feature.

Programming Additional Remote Controls

Instructions for adding or re-programming remote controls.

Critical Safety Instructions

Reduce Risk of Severe Injury or Death

Reinforces essential safety warnings for operation and maintenance.

Maintenance & Adjustments

Regular Maintenance Tasks

Lists essential monthly maintenance checks for the opener.

Safety System Checks & Tests

Covers Safe-T-Beam check, contact reverse test, and door balance.

Component Maintenance

Guides for lubricating hardware, replacing batteries, bulbs, and adjusting tension.

Adjustment Procedures

Details on adjusting carriage, force settings, and travel limits.

System Identification & Wiring

Information on locating sensors and the system's wire diagram.

Troubleshooting

General Operation Issues

Resolves problems with opener not operating, door movement, or unexpected activation.

Remote & Keypad Issues

Troubleshoots remote control range, operation, and lost/stolen devices.

Safety System Issues

Addresses Safe-T-Beam malfunctions and door stopping/opening problems.

Powerhead LED Status Codes

Interprets powerhead LED patterns to diagnose operational problems.

Genie Battery Backup Installation

Installing the Battery Backup

Step-by-step guide for installing the battery backup unit.

Testing Battery Backup

Procedure to test the functionality of the battery backup.

Replacing Battery Backup Battery

Instructions for safely replacing the battery in the backup unit.

Optional Programming & Accessories

Clearing Remote Memory

Steps to erase all programmed remotes and keypads from the opener.

Vehicle Programming

Programming HomeLink System

Steps to integrate the HomeLink system with the garage door opener.

Programming Car2U System

Instructions for programming the Car2U system to the opener.

Wireless Keypad Programming

Keypad Overview

Description of the wireless keypad's components and functions.

Keypad Programming Procedures

Guides for setting PIN, programming single/multiple openers, and resetting.

Keypad Operation & Management

Covers operating the keypad, replacing batteries, changing PINs, and mounting.

Replacement Parts

Replacement Parts Identification

Lists and identifies parts categorized by bag color and specific sets.

Single Bulb Powerhead Parts

Dual Bulb Powerhead Parts

DASMA Information & Safety Guide

Garage Door Openers Are Not Toys

Emphasizes safety, warning against children playing with openers.

Garage Door System Safety

Importance of proper installation, operation, and maintenance for safety.

Safety if Everyone's Business

Simple precautions to protect family and friends from potential harm.

Teaching Children Garage Door Safety

Educates on teaching children about safe operation and dangers.

Routine Maintenance for Safety

Encourages regular inspection and testing of the garage door system.

Testing & Maintaining Garage Door Opener

Steps for monthly safety and maintenance checks on the opener.

Reversal Test Procedure

How to test the opener's safety reversing feature.

Force Setting Test

How to test the opener's force setting during door closure.

Additional Safety Devices

Information on adding safety devices like photo eyes or edge sensors.

Door Lubrication

Guides on regularly lubricating moving door parts.

Door Balance Testing

How to periodically test and adjust the garage door's balance.

Opener Safety Information

General opener safety guidance from consumer safety organizations.

3 Button Remote Programming

Putting Opener into Programming Mode

Steps to prepare the opener for remote control programming.

Programming a Remote to Opener

Step-by-step guide to pair a remote control with the opener.

Lost or Stolen Remote / Erasing Remotes

Procedure to erase all remotes from memory for security.

Battery Replacement for Remote

Instructions for replacing the battery in the 3-button remote.

Related product manuals

Genie Excelerator 3531835447

32 pages

Genie 7035-TKV User Manual

Table of Contents

Questions and Answers:

Genie 7035-TKV Specifications

Summary

Safety Information

Safety Notifications

Important Safety Instructions

Features

Safety Features Overview

Opener Features Overview

Safety Notifications & Instructions

Overview of Potential Hazards

Conventions Used in Instructions

Important Safety Instructions

Installation Safety Instructions

Reduce Risk of Severe Injury or Death

Safety & Standard Features

Safety Systems

Operational & Connectivity Features

Wall Console Operation

Vehicle Compatibility

Opener Programming

Introduction to Programming

Powerhead Controls Overview

Programming Down Travel Limit

Programming Up Travel Limit

Programming Force and Contact Reverse

Programming Additional Remote Controls

Critical Safety Instructions

Reduce Risk of Severe Injury or Death

Maintenance & Adjustments

Regular Maintenance Tasks

Safety System Checks & Tests

Component Maintenance

Adjustment Procedures

System Identification & Wiring

Troubleshooting

General Operation Issues

Remote & Keypad Issues

Safety System Issues

Powerhead LED Status Codes

Genie Battery Backup Installation

Installing the Battery Backup

Testing Battery Backup

Replacing Battery Backup Battery

Optional Programming & Accessories

Clearing Remote Memory

Vehicle Programming

Programming HomeLink System

Programming Car2U System

Wireless Keypad Programming

Keypad Overview

Keypad Programming Procedures

Keypad Operation & Management

Replacement Parts

Replacement Parts Identification

Single Bulb Powerhead Parts

Dual Bulb Powerhead Parts

DASMA Information & Safety Guide

Garage Door Openers Are Not Toys

Garage Door System Safety

Safety if Everyone's Business

Teaching Children Garage Door Safety

Routine Maintenance for Safety

Testing & Maintaining Garage Door Opener

Reversal Test Procedure

Force Setting Test

Additional Safety Devices

Door Lubrication

Door Balance Testing

Opener Safety Information

3 Button Remote Programming

Putting Opener into Programming Mode

Programming a Remote to Opener

Lost or Stolen Remote / Erasing Remotes

Battery Replacement for Remote

Related product manuals