What causes the oil pump to stick in my GILES Fryer?
If the oil pump in your GILES Fryer is sticking, it might be due to: * Boil Out being run through the pump; disassemble and re-oil the pump. * Old oil being allowed to sit in the pump; run clean oil through the pump.
How to fix a GILES WOG-MP Fryer that will not turn on?
If your GILES Fryer won't turn on, and the power light and hood fan are not running, there are several potential causes. First, ensure the unit is connected to the correct power supply. Check your electrical panel for blown fuses or tripped breakers and replace or reset them as needed. Inspect the fuses and fuse holders inside the cabinet on the left side. Verify that the hood filter cover is properly closed and latched, ensuring the pin on the right corner engages the interlock switch. You may also need to check or replace the power switch. If the fire extinguisher system is not armed, contact Ansul service company. Lastly, if you have a manual control with ILS, make sure the PUSH TO START button is pressed and held for a few seconds.
Why is the oil smoking in my GILES WOG-MP Fryer?
If the oil in your GILES Fryer is smoking, it could be due to several reasons. The oil may have broken down from extended use, in which case you should change the oil. The cooking temperature might be too high; check and adjust the temperature setpoint. Dirty heating elements can also cause smoking, so perform a boil-out to clean them. Check and replace any failing elements. Ensure that the supply voltage is correct. Finally, maintain the oil level at the FULL mark.
What to do if my GILES WOG-MP is not heating up?
If your GILES Fryer's power light is on, the selector switch is in the cook position, but the heat light is off, consider these possible causes. First, the temperature setpoint may be below the actual oil temperature; check the setting, and if it's okay, begin cooking, noting that the heat light normally cycles on and off. If you see a “DRAIN OPEN” message and hear an alarm, fully close the valve to reset the alarm. You may need to check or replace the controller or temperature sensor. If you have computer control and see 'Er13' displayed, check the wiring and replace the sensor. Also, check and replace the contactor and the selector switch if necessary. Finally, if you have computer control, ensure the power-up procedure is completed by pressing [START] to begin PREHEAT.
Why is my GILES WOG-MP heating so slowly?
If your GILES Fryer is heating slowly and the heat light remains on constantly, it might be due to improper cooking procedures; consult the operations manual for correct methods. One or more heating elements could be faulty, so check and replace them as needed. A failing contactor, loose wiring, or low voltage coming to the fryer can also cause slow heating. Inspect and repair the wiring and supply power accordingly.
What does a pulsating tone from my GILES WOG-MP Fryer mean?
If your GILES Fryer (VH Model only) has the power light on, the selector switch in the cook position, the heat light off, and the buzzer is emitting a pulsating tone, consider these issues: * The EAC (Electrostatic Air Cleaner) may have shorted or bent fins; repair the EAC. * The EAC could be dirty; clean it. * The EAC Power Supply might be faulty; replace the high voltage power supply. * EAC wires may be shorted; remove the shorted condition. * The Contact Plate could be bad; replace it. * The EAC Module might be faulty; replace the EAC Module.
Why is oil not returning to the fry pot in my GILES WOG-MP Fryer?
If the oil is not returning to the fry pot in your GILES Fryer, here's what might be happening: * The Cook/Filter Switch may not be in the “Filter” position; place the selector switch in the correct position. * There could be an air leak (hose, fittings, filter paper); repair any leaks. * The pump motor might be bad and require replacement. * The oil pump could be sticking; try to free it. * The filter pan may contain too much sediment; remove and thoroughly clean it. * The filter pan might not be assembled correctly. * The oil in the filter pan may be below 200ºF; remove the filter pan and remove the cold oil.
What does it mean if the filter missing light is on in my GILES Fryer?
If your GILES Fryer (VH Model Only) has the power light on, the selector switch in the cook position, but the filter missing light is on, check the following: * Ensure the Baffle Filter is installed. If missing, install it. * If the Baffle Filter is present, make sure it is installed properly; reinstall if necessary. * Verify that the Charcoal Filter is installed. If missing, install it.
What should I do if my GILES Fryer displays a 'Clean the EAC' message?
If your GILES Fryer is not heating, the power light is on, the selector switch is in the cook position, the heat light is off, and you're experiencing a beeping tone alarm or a “CLEAN THE EAC” message with CHECK/WASH lights on, the EAC cell is likely excessively dirty and needs cleaning. Other potential issues include bent or shorted EAC cell fins, too many broken ionizer wires on the cell, a poor connection with the contact board, a faulty EAC power supply or shutdown module, or a missing EAC cell. Repair the EAC cell, replace ionizer wires, clean or replace the contact board, and replace the power supply or module as needed. Ensure the EAC cell is properly installed.
Why is the oil temperature erratic in my GILES WOG-MP Fryer?
If the oil temperature in your GILES Fryer is erratic, the temperature sensor may be faulty and need replacement. A failing contactor, a faulty controller or thermostat, or loose wiring can also cause this issue. Check and repair any loose wiring, and replace the contactor, controller, or thermostat as necessary.
To Next Page
General
