Globalstar ST100 - Page 5

8545-0194-01 v1.0
III
4.2.2. Serial Packet Command List .............................................................................................................30
4.2.2.1. Send Data (0x00) ...............................................................................................................31
4.2.2.2. Query Electronic Serial Number (ESN) (0x01) .......................................................................31
4.2.2.3. Abort Transmission (0x03) ...................................................................................................31
4.2.2.4. Query Bursts Remaining (0x04) ...........................................................................................32
4.2.2.5. Query Firmware Version (0x05) ............................................................................................32
4.2.2.6. Setup (0x06)......................................................................................................................32
4.2.2.7. Query Setup (0x07) ............................................................................................................33
4.2.2.8. Query Hardware Version (0x09) ............................................................................................34
4.2.2.9. Set GPS Timeout command .................................................................................................35
4.2.2.10. Get GPS Timeout query .....................................................................................................35
4.2.2.11. “SPOT GEN3 emulation. ...................................................................................................35
4.2.2.12. Special consideration for “Byte 7” in the next several commands. .........................................36
4.2.2.13. “Proprietary Track” command ............................................................................................36
4.2.2.14. “Proprietary Motion Activated Track” command ...................................................................38
4.2.2.15. “Update Proprietary Track Data” command .........................................................................39
4.2.2.16. “Cancel Proprietary Track/Proprietary Motion Activated Track” command................................40
4.2.2.17. “Proprietary Track Status” query ........................................................................................41
4.2.2.18. “Tracking Statistics” query ................................................................................................42
4.2.2.19. “GPS Statistics” query ......................................................................................................43
4.2.2.20. “Transmitter Statistics” query. ...........................................................................................44
4.2.2.21. “Set Accelerometer On/Off” Command. ..............................................................................44
4.2.2.22. Accelerometer On/Off Query. ..............................................................................................45
4.2.2.23. “Send Redundant Burst with GPS” command .....................................................................45
4.2.2.24. “Query Location” command ...............................................................................................47
4.2.2.25. “Set Lifetime” command ...................................................................................................48
4.2.2.26. “Query Lifetime Status” command .....................................................................................49
4.2.2.27. “Set Minimum Track Rate” command .................................................................................49
4.2.2.28. “Query Minimum Track Rate” ............................................................................................50
4.2.2.29. “Suspend/Unsuspend” command .......................................................................................51
4.2.2.30. Suspended State query .....................................................................................................51
4.2.2.31. “Set Low Battery Rate” command ......................................................................................52
4.2.2.32. “Query Low Battery Rate” ..................................................................................................52
4.2.2.33. “Turn On GPS” command ..................................................................................................53
4.2.2.34. “Turn Off GPS” command .................................................................................................53
4.2.2.35. “Turn On GPS Pass-through” command ..............................................................................54
4.2.2.36. “Turn Off GPS Pass-through” command ..............................................................................55
4.3. ST100 BOARD SELF-TEST COMMAND ........................................................................................................56
4.4. HEALTH STATUS MESSAGING ...................................................................................................................57
4.5. BOOTLOADING. FIELD UPDATE OF DEVICE FIRMWARE ...............................................................................58
4.5.1. Nordic Nrf52832 Firmware Update Via Bootloader (“Buttonless” DFU) ................................................58
4.5.2. On Ax50324 Firmware Update Via Serial Bootloader ..........................................................................58
4.5.2.1. 0x60 “Enter Bootloader Command” .....................................................................................58
4.5.2.2. 0x61 “Flash One Line” .......................................................................................................59
4.5.2.3. 0x62 “Enter Application” ....................................................................................................60