go-e Controller User Manual

66 77
Any modication or repair to the hard-
ware or software of the go-e Controller
may only be carried out by qualied
specialist of go-e GmbH.
Before dismantling an allegedly defective pro-
duct, contact go-e's technical customer support
in any case and wait for their decision on the
further procedure for handling the service case.
Removing and damaging warning notices at-
tached to the go-e Controller or opening the
device will result in the loss of any liability by
go-e GmbH. The manufacturer's guarantee also
expires in the event of any modication or ope-
ning of a go-e Controller.
Do not cut the current transformer cables.
The go-e Controller is maintenance-free.The
device can be cleaned with a damp cloth. Do
not use any cleaning agents or solvents.
Opening, repair, maintenance
Legal notice
The copyright to these operating instructions is
held by go-e GmbH.
All texts and illustrations correspond to the
technical status at the time of preparation of
the manual. go-e GmbH reserves the right to
make unannounced changes. The contents
of the operating instructions do not justify any
claims against the manufacturer. Pictures are
for illustration purposes and may dier from
the actual product.
Disposal
According to guideline 2012/19/EU
(WEEE Directive), electrical equipment
must not be disposed of with house-
hold waste after the end of use. Take
the device to a collection point spe-
cially set up for waste electrical equipment in
accordance with national legal requirements.
Also dispose of the product packaging properly
in the waste paper collection so that it can be
recycled.
4. Safety regulations/notes
Electrical protective measures,
installation, operation
All information on electrical installa-
tion is intended exclusively for a qua-
lied electrician whose training allows
all electrical work to be carried out in
accordance with the applicable natio-
nal regulations.
The go-e Controller must be mounted by a qua-
lied electrician in accordance with the comple-
te operating instructions. The installation must
be carried out in accordance with local, regional
and national regulations.
An electric shock can be fatal. Disconnect the
circuit from the power supply before making
any electrical connections.
The Controller is mounted on a top-hat rail.
Observe the permissible ambient conditions.
At ambient temperatures of more than 45 °C, a
safety distance of 10 mm to other devices in the
control cabinet is recommended. An ambient
temperature of 55 °C must not be exceeded.
The Controller should not be operated in the
immediate vicinity of ammable or explosive
substances, running water or heat-emitting
equipment.
Make sure that the power connection leading
to the go-e Controller is properly installed and
undamaged.
An RCD type A, 30 mA must be provided on the
building side, unless local regulations deviate
from this. Independently of this, a line circuit
breaker (recommendation: LS-3/B6) must be
provided. Do not fuse the go-e Controller with
more than 16 A.
General safety regulations
The go-e Controller is to be used ex-
clusively to collect measured values in
an electrical system and to pass them
on in a network in order to implement energy
monitoring, to maximize the self-consumption
of a PV system or to implement dynamic load
management in interaction with go-e Chargers.
Failure to comply with the safety regulations
can have serious consequences. go-e GmbH
disclaims any liability for damage caused by
disregarding the operating instructions, safety
regulations or warnings on the device.
Mains voltage - danger to life! Never use the
go-e Controller if the housing is damaged or
open.
If unusual heat is generated, do not touch the
go-e Controller and disconnect the power sup-
ply. In case of discoloration or distortion of the
plastic, contact customer support.
Wearers of electronic implants should keep at
least 60 cm away from the go-e Controller due
to electromagnetic elds.
The go-e Controller has the communication
interface WiFi 802.11b/g/n 2.4GHz. The WiFi is
operated on a frequency of 2.4Ghz, channels
1-13 with the frequency band 2412-2472Mhz.
The maximum transmit power of the WLAN is
20dBm EIRP.
The go-e Controller may only be operated on
fully functional protective devices. Connection
cables must be suciently dimensioned. We
recommend a cable cross-section of at least 1.5
mm².
The current transformers should be attached
in the direction of the current as described and
illustrated in the installation instructions. This
means that the arrows on the current transfor-
mers should point in the direction of the cur-
rent consumer.
Always use the current transformers supplied.
Alternative current transformers, which are
also suitable for higher currents, may be used
only after inquiry to go-e support and its conr-
mation in text form.

go-e Controller Specifications

General

Enclosure	Plastic
Communication Interface	WiFi
Protocols	Modbus
Output Voltage	230 V
Frequency	50 Hz
Protection	Overcurrent, Overvoltage