What to do if my Goodwe Inverter shows Utility Loss?
If your Goodwe Inverter shows a 'Utility Loss' error, it means the grid is not connected. First, check the grid connection cables and make sure they are properly connected. Then, verify the grid's usability to ensure it is functioning correctly.
How to fix Over Temperature error on Goodwe GW1500-SS Inverter?
If your Goodwe inverter is showing an 'Over Temperature' error, it means the internal temperature is higher than the normal specified value. To resolve this: * Reduce the ambient temperature around the inverter. * Move the inverter to a cooler location. If the issue persists, further assistance may be needed.
What to do if Goodwe GW1500-SS shows Ground I Failure?
If your Goodwe Inverter displays a 'Ground I Failure', it indicates that the ground current is too high. Unplug the inputs from the PV generator and check the peripheral AC system. When the problem is cleared, reconnect the PV panel and check the inverter status.
How to troubleshoot Isolation Failure on a Goodwe Inverter?
To address an 'Isolation Failure' on your Goodwe Inverter, check the impedance between PV (+) & PV (-) and ensure the PV inverter is earthed. The impedance value must be greater than 2M?. If the problem persists, further assistance may be needed.
What causes PV Over Voltage on a Goodwe GW1500-SS Inverter?
If your Goodwe Inverter is showing a 'PV Over Voltage' error, check whether the PV open voltage is higher or too close to the maximum input voltage. If the problem still exists when the PV voltage is less than the maximum input voltage, further assistance may be needed.
What to do if my Goodwe GW1500-SS has Vac Failure?
If your Goodwe Inverter shows a 'Vac Failure', the PV Inverter will automatically restart within 5 minutes if the grid returns to normal. Also, make sure grid voltage conforms with the specification. If the problem still exists, further assistance may be needed.
What does Fac Failure mean on a Goodwe GW1500-SS?
If your Goodwe Inverter displays a 'Fac Failure', the PV Inverter will automatically restart within 5 minutes if the grid returns to normal. Also, make sure grid frequency is in conformity with the specification. If the problem still exists, further assistance may be needed.
How to resolve Consistent Failure on a Goodwe GW1500-SS?
If your Goodwe Inverter is experiencing a 'Consistent Failure', disconnect PV (+) or PV (-) from the input and restart the PV Inverter. If the problem still exists, further assistance may be needed.
What to do for Relay-Check Failure on Goodwe GW1500-SS?
To address a 'Relay-Check Failure' on your Goodwe Inverter: 1. Disconnect all PV (+) or PV (-). 2. Wait for a few seconds. 3. After the LCD switches off, reconnect and check again. If the message appears again, further assistance may be needed.
Why does my Goodwe Inverter shut down with Insufficient sunlight?
When sunlight is insufficient, the Goodwe PV Inverter may continuously start up and shut down automatically due to insufficient power generated by the PV panel. If the problem remains, further assistance may be needed.
Provides guidelines for physically mounting the inverter unit.
Details the process of physically installing the inverter unit.
Detailed steps for connecting the inverter to the AC power grid and DC input.
Provides solutions for common error messages and operational issues.
Lists error messages and their corresponding descriptions.
General| Model | GW1500-SS |
|---|---|
| Rated Power | 1500 W |
| Start Voltage | 80 V |
| Max. AC Power | 1500 W |
| Rated Output Voltage | 230 V |
| MPPT Efficiency | 99.9% |
| Protection Degree | IP65 |
| Output Frequency | 50 Hz / 60 Hz |
| Cooling | Natural Cooling |
| Type | Single Phase |
| MPPT Voltage Range | 80 V - 500 V |
| AC Voltage Range | 184 V - 264 V |
| Operating Temperature Range | -25 °C to +60 °C |
To Next Page
