Why is my Graco GH 300 Paint Sprayer spitting?
If your Graco Paint Sprayer is spitting from the gun, there are a few things you can check: * Make sure there is no air in the fluid pump or hose. Check for loose connections on the siphon assembly, tighten them, and then reprime the pump. * Tighten any loose intake suctions. * Refill the supply container if the fluid supply is low or empty.
Why is there excessive leakage around hydraulic motor piston rod wiper on my Graco Paint Sprayer?
If you notice excessive leakage around the hydraulic motor piston rod wiper on your Graco Paint Sprayer, it's likely that the piston rod seal is worn or damaged. Replace these parts to resolve the leakage.
What to do if the gas engine operates but the displacement pump doesn't on my Graco GH 300?
If the Graco Paint Sprayer's gas engine operates, but the displacement pump doesn't, check the following: * Ensure the hydraulic pump valve is set to ON. * Increase the pressure setting. * Clean the displacement pump outlet filter if it's dirty or clogged. * Remove and clean the tip or tip filter if clogged. * Shut off the sprayer and add hydraulic fluid if the level is low. * If the belt is worn, broken, or off, it should be replaced. * If the hydraulic pump is worn or damaged, take the sprayer to a Graco distributor for repair. * If dried paint has seized the paint pump rod, service the pump. * If the hydraulic motor is not shifting, set the pump valve to OFF, turn the pressure down, turn the engine OFF, and pry the rod up or down until the hydraulic motor shifts.
Why is the fluid delivery low on my Graco Paint Sprayer?
If the fluid delivery is low on your Graco Paint Sprayer, consider the following: * Increase the pressure setting. * Clean the displacement pump outlet filter if it is dirty or clogged. * Ensure the intake line to the pump inlet is tight. * If the hydraulic motor is worn or damaged, take the sprayer to a Graco distributor for repair. * Use a larger diameter or shorter hose to address a large pressure drop in the fluid hose.
How to fix a Graco GH 300 Paint Sprayer when the gas engine pulls hard?
If the gas engine on your Graco Paint Sprayer pulls hard and won't start, it could be due to high hydraulic pressure. Turn the hydraulic pressure knob counter-clockwise to the lowest setting.
Why is the output low on upstroke when displacement pump operates on my Graco Paint Sprayer?
If the displacement pump on your Graco Paint Sprayer operates, but the output is low on the upstroke, it could be due to: * A piston ball check not seating properly. Service the piston ball check. * Piston packings worn or damaged. Replace the packings.
What to do if displacement pump operates but output is low on downstroke on Graco GH 300 Paint Sprayer?
If the displacement pump operates but output is low on downstroke and/or on both strokes on your Graco Paint Sprayer, it could be due to: * Piston packings worn or damaged. Tighten the packing nut or replace the packings. * Intake valve ball check not seating properly. Service the intake valve ball check. * Suction tube air leak.
What to do if the electric motor does not operate on Graco Paint Sprayer?
If the electric motor on your Graco Paint Sprayer does not operate: * Ensure the power switch is turned ON. * Check the circuit breaker at the power source and reset the motor switch if it has tripped.
How to fix paint leaks and runs over side of wetcup on Graco GH 300 Paint Sprayer?
If paint leaks and runs over the side of the wet-cup on your Graco Paint Sprayer, it could be due to: * A loosen wet-cup. Tighten the wet-cup enough to stop the leakage. * Throat packings worn or damaged. Replace the packings.
Details risks related to flammable fumes and ignition sources.
Explains dangers of high-pressure fluid piercing skin.
Warns about fluid splashing and eye injury from system pressure.
Covers risks of improper grounding and electrical setup.
Warns about pinch and amputation risks from moving components.
Covers risks associated with improper usage and modification.
Details risks from chemicals, suction, CO, toxic fluids, burns.
Details the steps to safely relieve system pressure.
Provides a guide to diagnose and fix operational issues.
Outlines Graco's warranty coverage and limitations.
General| Engine | Honda GX160 |
|---|---|
| Horsepower | 5.5 HP |
| Power Source | Gasoline |
| Max Pressure | 3300 PSI |
| Hopper Capacity | 5 gallons |
| Hose Length | 50 feet |
| Voltage | Not Applicable |
To Next Page
