Graco Magnum X5 User Manual (English)

Other manuals for Graco Magnum X5

Questions and Answers:

L
lisarodriguezSep 4, 2025
Why is my Graco Magnum X5 Paint Sprayer motor overheating?
- G
  grahamscottSep 5, 2025
  If your Graco Paint Sprayer motor is hot and runs intermittently, clear any clogged vent holes in the shroud. Ensure the sprayer isn't covered. If you're using an extension cord, it should be of the correct gauge and length. Also, if using an electrical generator, make sure it has a proper voltage regulator and provides 220-240 VAC 50/60 Hz. Decrease the pressure setting or increase the tip size and move the sprayer to a cooler location.
P
Paula WalshSep 3, 2025
Why does Graco Paint Sprayer only dribble paint?
- A
  Andrea RichardsSep 4, 2025
  If your Graco Paint Sprayer pump cycles but the paint only dribbles or spurts, first, increase the pressure by turning the pressure control knob. Clean the spray tip. If the spray tip is too large or worn, replace it. Also, clean the gun filter and fluid filter.
M
michelle43Aug 23, 2025
Why did my Graco Paint Sprayer stop spraying?
- D
  Derrick HernandezAug 23, 2025
  If your Graco Paint Sprayer gun has stopped spraying, check the suction tube connection and tighten it if it's loose. Inspect for any cracks or vacuum leaks. Also, inspect and unclog the spray tip.
C
Christian BradleySep 2, 2025
How to unlock the trigger on a Graco Paint Sprayer?
- B
  Brett ChavezSep 2, 2025
  To unlock the trigger on your Graco Paint Sprayer, rotate the trigger safety lever to unlock the trigger lock.
T
Thomas WeaverSep 1, 2025
What to do if my Graco Magnum X5 pump does not prime?
- K
  Kristi BarberSep 1, 2025
  If your Graco Paint Sprayer pump does not prime, make sure the Prime/Spray Valve is in the PRIME position (pointing down). Check the inlet screen for clogs and ensure the suction tube is immersed in fluid. If you haven't already, prime the pump with water or solvent-based flushing fluid. Also, make sure that the suction tube is not leaking, allowing air to enter, and replace it if cracked or damaged.
A
Alexander MillerAug 31, 2025
What to do if the Graco Paint Sprayer pump cycles but doesn't build up pressure?
- A
  Austin JacksonAug 31, 2025
  If the pump of your Graco Paint Sprayer cycles but does not build up pressure, ensure that the Prime/Spray valve is in the SPRAY position (pointing forward). Also, make sure the pump is primed. Check that the inlet screen isn't clogged and that the suction tube is fully immersed in the fluid. Additionally, inspect the suction tube for any cracks or cuts, ensuring the clamp is securely on the hose; replace the tube if it's damaged.
C
Charles MaldonadoAug 30, 2025
What to do if Graco Paint Sprayer dribbles or spurts paint?
- J
  Jennifer QuinnAug 30, 2025
  If your Graco Paint Sprayer pump cycles but the paint only dribbles or spurts when you trigger the spray gun, first, make sure the pressure isn't set too low by slowly turning the Pressure Control Knob clockwise to increase the pressure. Also, check if the spray tip, InstaClean™ fluid filter, or spray gun fluid filter are clogged and clean or replace them as necessary. Finally, the spray tip might be too large or worn, requiring replacement.
S
scottbarnesAug 29, 2025
Why my Graco Magnum X5 Paint Sprayer pump cycles but does not build up pressure?
- M
  Mary MelendezAug 29, 2025
  If your Graco Paint Sprayer pump cycles but doesn't build up pressure, first, ensure the pump is properly primed. Check that the inlet screen isn't clogged and that the suction tube is fully immersed in the paint. Also, inspect the suction tube for any leaks and tighten the connection or replace the tube if necessary. If these steps don't resolve the issue, the Prime/Spray Valve may be worn or obstructed, requiring service at a Graco/MAGNUM authorized service center. Another potential cause is a stuck pump check ball; refer to the 'Pump does not prime' section for troubleshooting steps.
B
Billy ButlerAug 28, 2025
What to do if Graco Magnum X5 gun stops spraying?
- D
  Dennis CookAug 28, 2025
  If your Graco Paint Sprayer gun stops spraying, turn the arrow-shaped handle to the unclog position, aim the gun into a waste pail, squeeze the trigger, then return the handle to the spray position.
B
brenda94Aug 27, 2025
Why Graco Magnum X5 pump cycles but pressure doesn't build up?
- P
  pbanksAug 27, 2025
  If the Graco Paint Sprayer pump cycles but pressure doesn't build, first, ensure the pump is properly primed. Check the inlet screen for any clogs and clean them off. Verify the suction tube is fully immersed in the paint. Refill the paint pail if it's empty and re-prime the sprayer. Inspect the suction tube for air leaks and tighten the connection or replace if cracked. If the pump check ball is stuck, refer to the 'Pump will not prime' section and press the pump priming button two times.

Graco Magnum X5 Specifications

General

Type	Airless Paint Sprayer
Maximum Flow Rate	0.27 gallons per minute
Maximum Tip Size	0.015 inch
Maximum Operating Pressure	3000 PSI
Power Source	Electric
Voltage	120V
Maximum Hose Length	75 ft
Pressure Control	Adjustable
Recommended Annual Use	125 gallons per year
Motor	0.5 HP