Graco Magnum XR9 User Manual (English)

Other manuals for Graco Magnum XR9

Operating Instructions16 pages

Operation60 pages

Questions and Answers:

C
Christopher ScottAug 22, 2025
What to do if Graco Magnum XR9 Paint Sprayer pump will not prime?
- T
  Theresa PorterAug 22, 2025
  If your Graco Paint Sprayer pump isn't priming, several issues could be the cause. First, ensure the Prime/Spray valve is set to PRIME. Check and clean the inlet screen for any clogs. Make sure the suction tube is fully immersed in the paint. If the inlet valve check ball is stuck, try dislodging it by inserting a pencil into the inlet section. For a stuck outlet valve check ball, open the Easy-Access door, unscrew the outlet valve, and clean the assembly. Also, tighten the suction tube connection and inspect for any leaks. If the Prime/Spray valve is clogged, clean or replace the drain tube, but if the drain valve is clogged return the sprayer to an authorized service center.
A
Amy CannonAug 23, 2025
What to do if my Graco Paint Sprayer is not spraying?
- A
  Ashley HernandezAug 23, 2025
  If your Graco Paint Sprayer gun stops spraying, the spray tip is likely clogged. To fix this, turn the arrow-shaped handle to the unclog position, aim the gun into a waste pail, squeeze the trigger, and then return the handle to the spray position to resume spraying.
A
Amber MaysAug 25, 2025
Why does paint leaks down outside of pump with Graco Magnum XR9 Paint Sprayer?
- S
  Steven BerryAug 26, 2025
  If paint leaks down the outside of the pump with your Graco Paint Sprayer, the pump packings are likely worn. Replace the pump packings.
D
Dr. James Dawson Jr.Aug 26, 2025
What to do if Graco Paint Sprayer pump cycles but pressure does not build up?
- M
  Michelle GuzmanAug 27, 2025
  If your Graco Paint Sprayer pump is cycling but pressure isn't building up, first ensure the pump is primed. Check the inlet screen for clogs and clean if necessary. Make sure the suction tube is immersed in the paint and that the paint pail isn't empty; refill if needed and reprime the sprayer. Also, check the suction tube for air leaks and tighten the connection or replace the tube if cracked. If these steps don't resolve the issue, the pump check valves may be dirty or damaged, or the pump check ball may be stuck.
J
Jose HouseAug 27, 2025
Why is my Graco Magnum XR9's pressure set at maximum, but cannot achieve good spray pattern?
- R
  Robert WallerAug 27, 2025
  If your Graco Paint Sprayer's pressure is at maximum but you can't get a good spray pattern, the tip might be too large for the sprayer, so select a smaller one. Alternatively, the tip may be worn, so replace it. Also, check for a clogged inlet screen and clean any debris.
D
David EdwardsAug 28, 2025
Why is sprayed paint running down wall or sags with Graco Magnum XR9 Paint Sprayer?
- D
  Denise RodriguezAug 29, 2025
  If sprayed paint runs down the wall or sags when using your Graco Paint Sprayer, you're likely applying the paint too thickly, so move the gun faster. Alternatively, use a tip with a smaller hole size or a wider fan, or move the gun further away from the surface.
J
Jeffrey GallagherAug 30, 2025
Why is the pattern inconsistent or leaving stripes with Graco Magnum XR9?
- T
  Teresa PattonAug 30, 2025
  If the pattern is inconsistent or leaving stripes when using your Graco Paint Sprayer, the pressure might be set too low, so increase it. Also, the spray tip may be worn, so replace it.
A
Amanda LopezAug 31, 2025
What to do if paint runs down the wall when using my Graco Magnum XR9 Paint Sprayer?
- A
  Amy BrownAug 31, 2025
  If paint runs down the wall when using your Graco Paint Sprayer, it’s likely that the coat is going on too thick. Try moving the gun faster. Also, consider using a tip with a smaller hole size and a wider fan. Finally, ensure the gun is far enough from the surface.
R
Ronald KennedySep 1, 2025
What to do if the Graco Paint Sprayer motor does not turn on?
- C
  Chris AlexanderSep 1, 2025
  If the motor on your Graco Paint Sprayer doesn't turn on, first check if the electrical outlet is providing power, or if the extension cord or sprayer power cord is damaged; try a different outlet, reset the circuit breaker, or replace the cords. Another possibility is that the paint is frozen or hardened in the pump. If frozen, thaw it completely before attempting to start the sprayer. If the paint has hardened, the pump packings, valves, drivetrain, or pressure switch may need replacement.
C
Charles HillSep 3, 2025
What to do if my Graco Paint Sprayer pump cycles but doesn't build up pressure?
- R
  Rick SmithSep 3, 2025
  If your Graco Paint Sprayer pump cycles but doesn't build up pressure, the pump check valves may be dirty or damaged. In this case, you should clean or replace the check valves. Alternatively, the spray/prime valve may be worn or obstructed with debris.