Graco SaniForce Instructions And Parts

Graco SaniForce

14 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Instructions and Parts

SaniForce™ 6:

1 Sanitary Pumps

3A5564A

EN

Specially de

signed for use only in Graco SaniForce pail or drum unloader systems. For professional use

only.

Important

Safety Instructions

Read all wa

rnings and instructions in this manual and in related

system manuals. Save all instructions.

Maximum Working Air Pressure: 100

psi (0.7 MPa, 6.9 bar)

Maximum Working Fluid Pressure: 650

psi (4.5 MPa, 44.8 bar)

P

ROVEN QUALITY. LEADING TECHNOLOGY.

Table of Contents

Other manuals for Graco SaniForce

Operation64 pages

Instructions - Parts26 pages

Questions and Answers:

H
hardingerinJul 27, 2025
What to do if Graco SaniForce Water Pump will not prime properly or only pumps air?
- M
  Michele DelacruzJul 27, 2025
  If your Graco Water Pump won't prime or only pumps air, here's what you can check: * Ensure the air valve is open and the air line isn't clogged; if it is, open and clear it. * Increase the air pressure if it's not sufficient. * If the hand valve is closed or clogged, open and clear it. If the hand valve is dirty, worn, or damaged, clean or service it. * A worn or damaged piston may also be the cause. In this case, replace it.
A
Aaron FisherAug 1, 2025
Why will my Graco Water Pump ram not raise or lower?
- B
  Brian WrightAug 1, 2025
  If the ram on your Graco Water Pump won't raise or lower, consider these potential causes and solutions: * Make sure the air valve isn't closed or the air line clogged; open or clear them if necessary. * Increase the ram air pressure if it's insufficient. * Replace the piston if it's worn or damaged. * Ensure the hand valve is open and clear, not closed or clogged.
C
Christopher PierceAug 6, 2025
What to do if air assist valve will not hold drum down or push plate up on Graco SaniForce Water Pump?
- M
  Miguel JonesAug 7, 2025
  If the air assist valve on your Graco Water Pump won't hold the drum down or push the plate up, try the following: * Check for a closed air valve or clogged air line, and open or clear as needed. * Ensure sufficient air pressure by increasing it. * Clean any clogs in the valve passage.
B
butlerstevenAug 11, 2025
How to adjust ram speed on Graco SaniForce Water Pump if it raises and lowers too fast?
- J
  Juan PorterAug 12, 2025
  If the ram on your Graco Water Pump raises and lowers too quickly: * Decrease the air pressure if it is too high. * Adjust the travel rate by moving the director valve handle further open for faster travel or less open for slower travel.
A
amy97Aug 16, 2025
What to do if fluid squeezes past ram plate wipers on Graco SaniForce Water Pump?
- R
  rcruzAug 16, 2025
  If fluid is squeezing past the ram plate wipers on your Graco Water Pump: * Decrease the ram air pressure if it's too high. * Replace the wipers if they are worn or damaged.
M
Melissa SosaAug 21, 2025
Why is air leaking around the cylinder rod on my Graco Water Pump?
- R
  Roberto WeberAug 21, 2025
  If air is leaking around the cylinder rod of your Graco Water Pump, the rod seal is likely worn and needs to be replaced.

Graco SaniForce Specifications

General

Brand	Graco
Model	SaniForce
Category	Water Pump
Language	English

Related product manuals

Graco SaniForce 4150

Preview: Graco SaniForce 1040

Graco SaniForce 1040

Preview: Graco SaniForce 2150

Graco SaniForce 2150

Graco SaniForce Series

Preview: Graco Dyna–Star 239882

Graco Dyna–Star 239882

Preview: Graco SaniForce A Series

Graco SaniForce A Series

Preview: Graco 17C487

Preview: Graco Merkur

Preview: Graco G3 Series

Graco G3 Series

Preview: Graco Husky 1050

Graco Husky 1050

Preview: Graco Reactor 2 Series

Graco Reactor 2 Series