Graco ultra max 1095 User Manual (English)

Other manuals for Graco ultra max 1095

Instruction Manual24 pages

Manual24 pages

Instructions And Parts List28 pages

Operation8 pages

Questions and Answers:

A
Audrey MooreAug 22, 2025
Why is my Graco ultra max 1095 building circuit breaker opening?
- J
  Joseph RiosAug 22, 2025
  If the building circuit breaker opens when using your Graco Paint Sprayer, try these steps: * Switch to another circuit with less load. If your sprayer has a 15/20A or 10/12A switch, change to the lower value. * Repair or replace any damaged wiring or terminals, and securely reconnect all wires. * Correct any faulty conditions. * Consider replacing the motor. * Replace with a new pressure control board.
E
elizabethortizAug 23, 2025
What to do if my Graco Paint Sprayer motor won’t operate?
- J
  John WilliamsAug 23, 2025
  If your Graco Paint Sprayer motor won’t operate, here are a few things you can try: * If an error code (E=0X) is displayed or the LED is blinking, refer to page 18 for error code diagnostics. * Tighten any loose power connections and replace any damaged power switch, power cord, or extension cords. * Reset the circuit breaker if it has tripped. * Increase the pressure setting. Based on the results of this test, investigate for possible wiring, motor, control, transducer, or potentiometer problems.
S
Steven HayesAug 25, 2025
What to do if my Graco Paint Sprayer motor runs but the pump does not stroke?
- L
  Levi McdonaldAug 25, 2025
  If the motor of your Graco Paint Sprayer runs, but the pump does not stroke, consider the following: * Replace the pump pin if it is missing. Ensure the retainer spring is fully in the groove all around the connecting rod. * Replace the connecting rod assembly. * Inspect the drive housing assembly and gears for damage and replace if necessary.
J
Jeffrey MendezAug 27, 2025
How to troubleshoot my Graco ultra max 1095 when the motor won’t operate due to basic fluid pressure problems?
- A
  Angela SpencerAug 27, 2025
  If your Graco Paint Sprayer motor won’t operate due to basic fluid pressure problems, slowly increase the pressure setting to see if the motor starts. Also, relieve the pressure and refer to the separate gun, tip, or fluid filter instruction manual for cleaning.
S
Selena YoungAug 27, 2025
What to do if my Graco ultra max 1095 motor won't operate due to electrical supply issues?
- J
  Jessica HaynesAug 27, 2025
  If your Graco Paint Sprayer motor won't operate, first reset the building circuit breaker or replace the fuse, and try another outlet. If the extension cord is damaged, replace it. Also, replace the power supply cord if it has broken insulation or wires.
L
Luis MorrisAug 29, 2025
How to reset the pressure control safety circuit on a Graco ultra max 1095 if the motor won't operate?
- K
  Katrina EvansAug 29, 2025
  If the motor of your Graco Paint Sprayer won't operate, try turning the pressure control ON/OFF switch to OFF to RESET it. If the pressure control safety continues to trip, see ELECTRICAL SHORT on page 8.
R
Ryan SanchezAug 30, 2025
How to adjust the pressure control knob if my Graco ultra max 1095 motor won't operate?
- A
  Adrian SchneiderAug 30, 2025
  If the motor of your Graco Paint Sprayer won't operate, slowly increase the pressure setting to see if the motor starts.
M
mdavisAug 31, 2025
What to do if the displacement pump connecting rod pin is causing my Graco Paint Sprayer motor not to operate?
- X
  xsmithAug 31, 2025
  If the motor of your Graco Paint Sprayer won't operate, check the displacement pump connecting rod pin. Push the pin into place and secure it with the spring retainer.
M
Maria GordonSep 2, 2025
What causes low output in a Graco ultra max 1095 Paint Sprayer, related to motor leads?
- M
  Melanie LambSep 2, 2025
  If your Graco Paint Sprayer has low output, check the leads from the motor to the pressure control circuit board for damaged or loose wires or connectors. Ensure the male terminal blades are centered and firmly connected to the female terminals. Replace any loose terminals or damaged wiring, and securely reconnect the terminals.
D
Danielle MillerSep 3, 2025
How to fix low output in my Graco ultra max 1095 Paint Sprayer due to loose motor brush leads?
- J
  Joshua GibsonSep 3, 2025
  If your Graco Paint Sprayer has low output, it could be due to loose motor brush leads and terminals. Tighten the terminal screws and replace the brushes if the leads are damaged.