GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY
Keine Haftung für Druckfehler. Technische Änderungen vorbehalten! ID# 47496 10/2003
28
46 Side window cladding 2 Plywood CNC-machined, 1.0 mm
47 Central window frame 1 Plywood CNC-machined, 1.0 mm
48 Rear bridge panel 1 Plywood CNC-machined, 1.0 mm
49 Bridge deck 1 Plywood Laser-processed, 1.0 mm
50 Bridge step 1 Plywood Laser-processed, 1.0 mm
51 After deck 1 Plywood Laser-processed, 1.0 mm
52 Fore deck 1 Plywood Laser-processed, 1.0 mm
53 Guard rail 19 ABS 1.0 mm Ø rod, overlength
54 Screening plate 1 ABS As plan, make from scrap
55 Roof 1 ABS Vac.-moulded, 1.0 mm
56 Spacer 2 ABS or wood approx. 60 x 10 x 1 mm, make from scrap
57 Cockpit 1 ABS Vac.-moulded, 1.0 mm
58 Bottom cockpit section 1 ABS Vac.-moulded, 1.0 mm
59 Companionway 1 ABS Vac.-moulded, 1.0 mm
60 Skipper’s seat 1 ABS Vac.-moulded, 1.0 mm
61 Upper bench seat (long) 1 ABS Vac.-moulded, 1.0 mm
62 Upper bench seat (short) 1 ABS Vac.-moulded, 1.0 mm
63 Lower bench seat (short, left) 1 ABS Vac.-moulded, 1.0 mm
64 Lower bench seat (long) 1 ABS Vac.-moulded, 1.0 mm
65 Lower bench seat (short, right) 1 ABS Vac.-moulded, 1.0 mm
66 Back panel 1 ABS As plan, make from scrap
67 Table base 2 ABS Vac.-moulded, 1.0 mm
68 Table leg 2 Aluminium 4 / 3.2 Ø x 30 mm
69 Upper table top 1 ABS Vac.-moulded, 1.0 mm
70 Lower table top 1 ABS Vac.-moulded, 1.0 mm
71 Upper table bottom section 1 ABS Vac.-moulded, 1.0 mm
72 Lower table bottom section 1 ABS Vac.-moulded, 1.0 mm
73 Upper table top insert 1 Plywood Laser-processed, 1.0 mm
74 Lower table top insert 1 Plywood Laser-processed, 1.0 mm
75 Rear bridge panel handrail 1 Beech Flexible wood strip, 5 x 2 x 110 mm
76 Side window frame 4 Plywood CNC-machined, 1.0 mm
77 Outer window frame 2 Plywood CNC-machined, 1.0 mm
78 Outer central window frame 1 Plywood CNC-machined, 1.0 mm
79 Inner window frame 2 Plywood CNC-machined, 1.0 mm
80 Central inner window frame 1 Plywood CNC-machined, 1.0 mm
81 Ventilator flaps 6 ABS 15 x 4 x 1 mm, make from scrap
82 Trim rail, left, side 1 ABS 3.2 x 1.5 mm, half-round, overlength
83 Trim rail, front, left 1 ABS 3.2 x 1.5 mm, half-round, overlength
84 Trim rail, centre 1 ABS 3.2 x 1.5 mm, half-round, overlength
85 Trim rail, front, right 1 ABS 3.2 x 1.5 mm, half-round, overlength
86 Trim rail, right, side 1 ABS 3.2 x 1.5 mm, half-round, overlength
87 Handrail, left 1 Beech Flexible wood strip, 5 x 2 x 110 mm
88 Handrail, right 1 Beech Flexible wood strip, 5 x 2 x 110 mm
89 Handrail stanchions 7 Plastic Ready made
90 Handrail 1 ABS 2 mm Ø round rod, overlength
91 Derrick base 1 ABS Vac.-moulded, 1.0 mm
92 External derrick outrigger 1 ABS Vac.-moulded, 1.0 mm
93 Internal derrick outrigger 1 ABS Vac.-moulded, 1.0 mm
94 Tongue 1 Plastic Ready made
95 Turnbuckle 1 Plated brass Ready made
96 Split pin 1 Metal Ready made
97 Inflatable boat, bottom shell 1 ABS Vac.-moulded, 1.0 mm
98 Inflatable boat, top shell 1 ABS Vac.-moulded, 1.0 mm
99 Outboard motor shells 2 ABS Vac.-moulded, 1.0 mm
100 Shaft spigot 1 ABS 1 mm Ø round rod, length approx. 10 mm
101 Propeller 1 Plastic 20 mm Ø, ready made
102 Inflatable boat supports 2 ABS or wood As plan, make from scrap
103 Inflatable boat cover 1 ABS Vac.-moulded, 1.0 mm
104 Steering wheel 2 Plastic Ready made
105 Throttle lever 1 Plated steel 1.5 mm Ø x 20 mm
To Next Page
Loading...
